background image

SPECIFICATIONS

GENERATOR

 

‹

Type ............................................................................. Synchronous
Rotor Insulation ................................................................... Class H
Stator Insulation .................................................................. Class H
Total Harmonic Distortion ..........................................................<5%
Telephone Interference Factor (TIF) ..........................................< 50
Alternator Output Leads 3-phase ........................................... 4-wire
Bearings .........................................................................Sealed Ball
Coupling .......................................................................Flexible Disc
Load Capacity (Standby Rating) .......................................22/27kW*
*

  NOTE: Generator rating and performance in accordance with ISO8528-5, BS5514, SAE J1349, 

ISO3046 and DIN 6271 Standards. KW rating is based on LPG fuel and may derate with natural 

gas and generator spcific settings.

Excitation System ....................................................................Direct
Generator Output Voltage/kW - 60 Hz 

kW 

Amp 

CB Size

  120/240V, 1-phase, 1.0 pf 

22/27 

92/113  100/125

  120/208V, 3-phase, 0.8 pf 

22/27 

77/94 

80/100

Generator Locked Rotor KVA Available @ Voltage Dip of 35%
  Single-phase (22/27kW) ................................................ 43/53 KVA
  208V, 3-phase (22/27kW) .............................................. 55/67 KVA

ENGINE

 

‹

Make ................................................................................... Generac
Model ..................................................................................... In  Line
Cylinders and Arrangement ............................................................ 4
Displacement ....................................................................... 2.4  Liter
Bore .....................................................................86.5 mm (3.41 in.)
Stroke ...................................................................100 mm (3.94 in.)
Compression Ratio ...............................................................9.5-to-1
Air Intake System ...............................................Naturally Aspirated
Valve Seats ....................................................................... Hardened
Lifter Type .......................................................................... Hydraulic

Engine Parameters

Rated Synchronous RPM ..............................................60 Hz, 1800
HP at rated kW (22/27kW) ...........................................60 Hz, 36/44

Exhaust System

Exhaust Flow at Rated Output 60 Hz (22/27kW) ......... 180/230 cfm
Exhaust Temp. at Rated Output (22/27kW) ................... 800°/850° F

Combustion Air Requirements (Natural Gas)

Flow at rated power, 60 Hz (22/27kW) ............................. 60/75 cfm

Governor

Type .................................................................................. Electronic
Frequency Regulation ...................................................Isochronous
Steady State Regulation ......................................................± 0.25%

Engine Lubrication System

Type of Oil Pump ...................................................................... Gear
Oil Filter ............................................... Full Flow Spin-on, Cartridge
Crankcase Oil Capacity ...............................................5.25 U.S. qts.

(including oil filter capacity)

COOLING SYSTEM

 

‹

Type ...................................................Pressurized Closed Recovery
Water Pump .................................................................... Belt Driven
Fan Speed .........................................................................1980 rpm
Fan Diameter ..............................................460 mm (18-1/8 inches)
Fan Mode ..............................................................................Pusher
Air Flow (inlet air including alternator and
  combustion air) ...........................................................2200 ft

3

/min.

Coolant Capacity ........................................................ (3.0 U.S. gal.)
Heat Rejection to Coolant ..........................................104,000 Btu/h
Maximum Operating Air Temp. on Radiator ..............60° C (150° F)
Maximum Ambient Temperature ................................50° C (140° F)

FUEL SYSTEM

 

‹

Type of Fuel ......................................... Natural Gas, Propane Vapor
Carburetor ...................................................................... Down Draft
Secondary Fuel Regulator .................................................Standard
Fuel Shut-off Solenoid ........................................................Standard
Operating Fuel Pressure  ...................... 5 in. - 14 in. Water Column

Fuel Consumption - ft

3

/hr (Natural Gas/LPV)

 Exercise 

25% 

50% 

75% 

100%

 Cycle 

Load 

Load 

Load 

Load

22kW 42/16 100/38 190/98  255/98 316/120
27kW 42/16 108/44 197/81 287/118 359/147

ELECTRICAL SYSTEM

 

‹

Battery Charge Alternator ............................................12V, 30 Amp
Static Battery Charger .........................................................2.5 Amp
Recommended Battery ...................................... Group 26, 525CCA
System Voltage .....................................................................12 Volts

Voltage Regulator

Type .................................................................................. Electronic
Sensing ........................................................................ Single-phase
Regulation ................................................................................± 1%
Features ................................................. V/F Adjustable, Adjustable 

Voltage and Gain LED Indicators

Power Adjustment for Ambient Conditions

Temperature Deration
  3% for every 10° C above °C (22/27kW) ................................... 25
  1.65% for every 10° above °F (22/27kW) .................................. 77
Altitude Deration
  1% for every 100 m above m (22/27kW) ................................. 183
  3% for every 1000 ft. above ft. (22/27kW) ................................ 600

Controller .............................................. R-200B

6-1

Standby Generator Sets

Specifications

GenSpec046  Rev.

 B  08/08

Summary of Contents for 2.4L

































































Reviews: