manualshive.com logo in svg

Carl Valentin Spectra II Series, Operating Manual

Share
Download
Carl Valentin Spectra II Series Operating Manual Download Page 10

Safety Instructions 

Spectra II Series 

 

10 

Betriebsanleitung 

10.16 

 

2.1  Operating Conditions 

Before initial operation and during operation

 these operating 

conditions have to be observed to guarantee save and interference-
free service of our printers. 

Therefore please carefully read these operating conditions. 

Shipment and storage of our printers are 

only

 allowed in original 

packing. 

Installation and initial operation of printer is only allowed if operating 
conditions were 

fulfilled

. 

Initial operation, programming, operation, cleaning and service of our 
printers are only recommended after careful study of our manuals. 

Operation of printer is only allowed by especially trained persons. 

 

NOTICE! 

Perform trainings regularly. 
Content of the training are chapter 2.1 (Operating Conditions), 
chapter 5 (Loading Media) and chapter 7 (Maintenance and 
Cleaning). 

These indications are also valid for someone else's equipment 
supplied by us. 

Only use original spare and exchange parts. 

Please contact the manufacturer with respect to spare/wear parts. 

 

 

The installation place of printer should be even, free of vibration and 
currents of air are to be avoided. 

The printers have to be installed to ensure optimal operation and 
servicing. 

 

 

The installation of the power supply to connect our printers has to be 
effected according to the international rules and regulations, 
especially the recommendations of one of the three following 
commissions: 

 

International Electronic Commission (IEC) 

 

European Committee for Electro technical Standardisation 
(CENELEC) 

 

Verband Deutscher Elektrotechniker (VDE) 

Our printers are constructed according to VDE and have to be 
connected to a grounded conductor. The power supply has to be 
equipped with a grounded conductor to eliminate internal interfering 
voltage. 

 

Conditions for 
installation place 

Installation of 
power supply 

Summary of Contents for Spectra II Series



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands