
CANYON FURNITURE COMPANY.
A.- (1) HEADBOARD
B.- (1) TOP BUNK BED
C.- (2) METAL DOWEL PINS
D.- (1) 6 DRAWER DRESSER
E.- (1) 3 DRAWER COMPUTER DESK
F.- (4) SIDE RAILS
G.-(2) GUARD RAILS
H.- (24) 80MM FLAT HEAD BOLTS
I.- (24) 5/8" CROSS DOWEL NUTS
J.- (1) 5MM ALLEN WRENCH
K.- (4) SLATS
L.- (8) 1 1/4" SCREWS
M.- (1) HEADBOARD
N.- (1) FOOTBOARD
O.- (1) LADDER
P.- (2) METAL HOOK BRACKETS
Q.- (6) 1" SCREWS
1.- TO ASEMBLE TWIN BUNK BED, USING ONE HEADBOARD (A), ONE TOP BUNK BED (B), TWO SIDE RAILS (F), TWO GUARD RAILS (G), ONE 6 DRAWER DRESSER (D) OR ONE 3 DRAWER COMPUTER DESK (E)
2.- REMOVE FACTORY INSTALLED PLASTIC PLUGS FROM THE TOP OF DRESSER OR THE TOP OF THE DESK , THEN INSERT ONE METAL DOWEL PIN ( C ) IN EACH HOLE OF THE TOP, TAKE THE TOP BUNK BED END (B)
PLACE IT ON TOP OF THE DRESSER OR DESK WITH THE GROVE LINES FACING LIKE FIG.8, ALIGNING THE METAL DOWEL PINS WITH THE BOTTOM HOLES OF TOP BUNK BED END UNTIL ARE ALL THE WAY IN, SEE FIG.8
3.- INSERT TWO CROSS DOWELS (I) IN ACCESS HOLE INSIDE THE SIDE RAIL & GUARD RAIL, ALIGN THE CROSS DOWEL NUT, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.9
4.- ATTACH TWO SIDE RAILS (F),TWO GUARD RAILS (G) TO HEADBOARD (A)&TOP BUNK BED (B),INSERTING TWO 80MM FLAT HEAD BOLTS (H) INTO HEADBOARD&TOP BUNK BED HOLES,USE THE 5MM ALLEN WRENCH
(j) TO TIGHTEN BOTH FLAT HEAD BOLTS
( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER ),
REPEAT THE SAME PROCESS AT ALL FOUR CORNERS, SEE FIG.10
5.- PLACE 4 SLATS (K) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH HEADBOARD&TOP BUNK BED ENDS, PUSH THE SLATS AGAINST THE BED END POST (FIG.A) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE
FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (L), SEE FIG.11
( USE ONE 4 PCS SLAT PACK (98-645) )
LIST OF CONTENTS
COTTAGE COLORS COLLECTION
BUNK BED END BOX ( 98-706 ) FIG.1
BUNK BED TOP END BOX ( 98-705 ) FIG.2
HARDWARE PACK
(HPK00012)
6 DRAWER DRESSER BOX ( 98-208 ) FIG.3
3 DRAWER COMPUTER DESK BOX ( 98-602 ) FIG.3
6 PCS SIDE RAILS BOX ( 98-730 ) FIG.4
HARDWARE PACK
(HPK00104)
4 PCS SLAT PACK BOX ( 98-645,98-646 ) FIG.5
LADDER BOX ( 98-720 ) FIG.7
HARDWARE PACK
(HPK00008)
HARDWARE PACK
(HPK00016)
TWIN/FULL BED BOX ( 98-707,98-709 ) FIG.6
TWIN BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 2
FIG. 9
B
C
FIG. 2
D
E
P
FIG. 3
O
G
H
F
I
J
FIG. 4
N
M
FIG. 5
K
L
FIG. 6
Q
FIG. 7
YES,
HORIZONTAL GROOVE
NO
FIG. 8
A
FIG. 1
FIG. 10
FIG. 11
REV 01 02/08/16
PAGE 3 OF 5
KIS01130
Summary of Contents for 98-161
Page 12: ......