CANYON FURNITURE COMPANY.
1.- PROCEED TO ASSEMBLE THE STEP UNIT, FIRST CHOOSING THE CONFIGURATION THAT FITS YOUR ROOM,
LEFT OR RIGHT
SEE FIG. 12, IF LEFT GO TO STEP #3 OR RIGHT GO TO STEP #2
2.- CHANGE DOOR THAT IS FACTORY INSTALLED IN LEFT SIDE TO THE RIGHT SIDE, USING A PHILLIPS SCREWDRIVER
(NOT INCLUDED),
REMOVE SCREWS FROM CASE PORTION OF THE HINGES, KEEP THE HINGES
FOR ATTACH THE DOOR (FIG.12)
( SAVE THE SCREWS TO RE-ATTACH THE DOOR TO RIGHT SIDE)
,THEN INSTALL DOOR ON THE RIGHT SIDE.
3.-TAKE THE BACK FRAME (F), PLACE IT IN THE BACK OF STEP UNIT (A), ALIGNING THE BACK FRAME HOLES WITH THE METAL INSERTS, FASTENING WITH FOUR 1 1/2" PAN HEAD SCREWS (L), SEE FIG.13
4.- REMOVE FIRST, SECOND AND FOURTH DRAWERS FROM STEP UNIT ( A), ALIGNING HANDRAIL HOLES ( E) WITH STEP UNIT HOLES INTHE SAME SIDE DOOR, INSERTING ONE 35MM BOLT ( H ) FROM OUTSIDE ON OF
HANDRAIL, ALIGNING HANDRAIL HOLE WITH BACK FRAME HOLE IN THE TOP, INSERTING ONE 100MM BOLT ( G) THEN INSERT ONE CAP NUT ( I) IN EACH BOLT, FASTEN USING ALLEN WRENCH ( J, K ), TIGHT ALL BOLTS
UNTIL SECURE, SEE FIG.13
5.- TO ATTACH TO TWIN TOP BUNK BED ASSEMBLY WITH STEP BUNK BED ASSEMBLY,ALIGNMENT HOLES ON BOTH SIDES,INSERT ONE 35MM BOLT IN BOTTOM HOLE AND ONE 100MM BOLT IN TOP HOLE,AND INSERT
ONE CAP NUT IN BOTH BOLTS AND FASTEN USING ALLEN WRENCH, SEE FIG.14
6.- REPLACE BACK THE DRAWERS AND MOVE STEP BUNK BED TO THE FINAL POSITION.
1.- ASSEMBLE BED, USING ONE HEADBOARD (V), ONE FOOTBOARD (V) AND TWO SIDE RAILS (M).
2.- INSERT TWO CROSS DOWELS (P) IN ACCESS HOLE INSIDE THE SIDE RAIL, ALIGN THE CROSS DOWEL NUT, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.9
3.- ATTACH TWO SIDE RAILS ( M ), TO HEADBOARD ( U ) & FOOTBOARD ( V), INSERTING TWO 80MM FLAT HEAD BOLTS ( O ) INTO TO HEADBOARD & FOOTBOARD HOLES, USE THE 5MM ALLEN WTENCH ( K) TO TIGHTEN
BOTH FLAT HEAD BOLTS
( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER ),
REPEAT THE SAME PROCESS AT ALL FOUR CORNERS, SEE FIG.15
4.- PLACE FOUR SLATS (S) ON TOP SIDE RAIL CLEATS,ONE SLAT IN BOTH HEADBOARD&FOOTBOARD ENDS,PUSH THE SLATS AGAINST THE BED END POST (FIG.A) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE
FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (T), SEE FIG.15
( USE ONE 4 PCS SLAT PACK FOR 98-707 (98-645) )
AND
( USE ONE 4PCS SLAT PACK FOR 98-709 (98-646) )
5.- PLACE IT UNDER THE STEP BUNK BED, AS SHOWN IN
CONFIGURATION # 2
2.- USE THE SHORT END OF THE ALLEN WRENCH FOR FINAL
TWIN/FULL BED ASSEMBLY
TIPS : SEE ILLUSTRATION BELOW
1.- USE THE LONG END OF THE ALLEN WRENCH TO FASTEN
TIGHTENING.
BOLTS LOOSELY AND QUICKLY.
STEP BUNK BED UNIT ASSEMBLY
FIG. 12
FIG. 13
STEP UNIT
FIG. 14
TIPS # 1
TIPS # 2
FIG. 15
REV 01 01/08/16
PAGE 5 OF 6
KIS01129
Summary of Contents for 98-161
Page 12: ......
