Canyon 98-161, Assembly Instructions Manual

Page: 13 / 14

CANYON FURNITURE COMPANY.
A.- (1) TOP BUNK BED END
B.- (2) METAL DOWEL PINS
C.- (1) 6 DRAWER DRESSER
D.- (1) COMPUTER DESK
E.- (4) SIDE RAILS
F.- (2) GUARD RAILS
G.- (24) 80MM FLAT HEAD BOLTS
H.- (24) 5/8" CROSS DOWEL NUTS
I.- (1) 5MM ALLEN WRENCH
J.- (1) LADDER
K.- (2) METAL HOOK BRACKETS
L.- (6) 1" SCREWS
M.- (1) HEADBOARD
N.- (1) FOOTBOARD
O.- (4) SLATS
1.- USE THE LONG
END OF THE ALLEN WRENCH (Q) TO FASTEN
BOLTS LOOSELY AND QUICKLY.
P.- (8) 1 1/4" SCREWS
2.- USE THE SHORT END OF THE ALLEN WRENCH FOR FINAL
TIGHTENING
AS SHOWN IN FIG.C
1.- TO ASSEMBLE THIS BUNK BED, USING TWO TOP BUNK BED ENDS (A), ONE 6 DRAWER DRESSER (C), ONE COMPUTER DESK (D), TWO SIDE RAILS (E) AND TWO GUARDRAILS (F).
2.- REMOVE FACTORY INSTALLED PLASTIC PLUGS FROM THE TOP OF DRESSER AND THE TOP OF THE DESK, THEN INSERT ONE METAL DOWEL PIN (B) IN EACH HOLE OF THE TOP, TAKE THE TOP BUNK BED END (A)
PLACE IT ON TOP OF THE DRESSER & DESK WITH THE GROVE LINES FACING LIKE FIG.8, ALIGNING THE METAL DOWEL PINS WITH THE BOTTOM HOLES OF TOP BUNK BED END UNTIL ARE ALL THE WAY IN, SEE FIG.8
3.- INSERT TWO CROSS DOWELS (H) IN ACCESS HOLE INSIDE THE SIDE RAIL & GUARD RAIL, ALIGN THE CROSS DOWEL NUT, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.9
4.-ATTACH TWO SIDE RAILS (E),TWO GUARD RAILS (F) TO BOTH TOP BUNK BED ENDS (A),INSERTING TWO 80MM FLAT HEAD BOLTS (G) INTO TOP BUNK BED END HOLES,USE THE 5MM ALLEN WRENCH (I) TO TIGHTEN
BOTH FLAT HEAD BOLTS
( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER ),
REPEAT THE SAME PROCESS AT ALL FOUR CORNERS, SEE FIG.10
5.- PLACE FOUR SLATS ( O) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH TOP BUNK BED ENDS, PUSH THE SLATS AGAINST THE BED END POST ( FIG. A ) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE FROM
THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (P), SEE FIG.11
( USE ONE 4 PCS SLAT PACK (98-645) )
HARDWARE PACK
(HPK00016)
TIPS : SEE ILLUSTRATION BELOW
3 DRAWER COMPUTER DESK BOX ( 98-602 ) FIG.3
6 PCS SIDE RAILS BOX ( 98-730 ) FIG.4
HARDWARE PACK
(HPK00008)
HARDWARE PACK
(HPK00104)
5MM ALLEN WRENCH ( INCLUDED )
TOOLS NEEDED
PHILLIPS HEADSCREWDRIVER (NOT INCLUDED)
LADDER BOX ( 98-720 ) FIG.5
TWIN/FULL BED BOX ( 98-707,98-709 ) FIG.6
4 PCS SLAT PACK BOX ( 98-645,98-646 ) FIG.7
COTTAGE COLORS COLLECTION
BUNK BED TOP END BOX ( 98-705 ) FIG.1 (2 BOXES)
HARDWARE PACK
(HPK00012)
( 98-705 ) COTTAGE COLORS COLLECTION BUNK BED ASSEMBLY INSTRUCTIONS
LIST OF CONTENTS
6 DRAWER DRESSER BOX ( 98-208 ) FIG.2
A
C
B
D
J
K
FIG.1
FIG.2
FIG.6
FIG.5
FIG.3
MAKE SURE ALL BOLTS ARE TIGHTENED
COMPLETELY
F
G
E
H
I
FIG. 4
L
M
N
P
O
FIG.7
FIG. 8
FIG. 9
YES,
HORIZONTAL GROOVE
NO
FIG. 10
FIG. 11
FIG. A
TO ASSEMBLE THIS BUNK BED REQUIRES TWO
PERSONS
REV 01 08/08/16
PAGE 1 OF 2 KIS01131