Canyon 98-161, Assembly Instructions Manual

Page: 3 / 14

CANYON FURNITURE COMPANY.
1.- TO ASEMBLE STEP BUNK BED, USING ONE HEADBOARD (B), ONE FOOTBOARD (C), FOUR SIDE RAILS (L), TWO GUARD RAILS (M) AND TWO EXTENTION KITS (R).
2.- INSERT TWO CROSS DOWELS (O) IN ACCESS HOLE INSIDE THE SIDE RAIL, ALIGN THE CROSS DOWEL NUT, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.8
3.- TO ATTACH TWO SIDE RAILS (L), AND TWO GUARD RAILS (M) ON TOP, REPEAT THE SAME PROCESS AS SHOWN IN FIG.9
4.- ATTACH EXTENTION KIT ( R), USING ONE METAL PLATE (S), FOUR 17.4MM BOLTS (T), FOUR CAP NUTS (H), ALIGN THE EXTENTION KIT WITH THE BOTTOM HEADBOARD & FOOTBOARD, THEN ALIGNED METAL PLATE
GROOVE FROM INSIDE WITH HEADBOARD & FOOTBOARD &EXTENTION KIT HOLES, FASTEN BY INSERTING FOUR 17.4MM BOLTS FROM INSIDE AND FOUR CAP NUTS FROM OUTSIDE, USE THE 5MM ALLEN WRENCH (J)
TO TIGHTEN BOLTS UNTIL SECURE, REPEAT THE SAME PROCESS IN EACH SIDE, SEE FIG.B
5.- TO ATTACH BOTTOM SIDE RAILS, USE THE SAME PROCESS AS SHOWN IN TOP SIDE RAILS, SEE FIG.9, USING TWO SIDE RAILS TO HDBD&FTBD BOTTOM HOLES, SEE FIG.11, TIGHT ALL BOLTS UNTIL SECURE.
6.- PLACE FOUR SLATS (P) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH HDBD & FTBD ENDS, PUSH THE SLATS AGAINST THE BED END POST (FIG. A) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE FROM THE
END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (Q), SEE FIG.12
( USE ONE TWIN 4 PCS SLAT PACK ( 98-645 )
7.- PLACE FOUR SLATS (P) ON BOTTOM SIDE RAIL CLEATS, ONE SLAT IN BOTH HDBD & FTBD ENDS, PUSH THE SLATS AGAINST THE BED END POST (FIG.A) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE FROM
THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (Q), SEE FIG.12
( USE ONE FULL 4 PCS SLAT PACK ( 98-646 )
1.- PROCEED TO ASSEMBLE THE STEP UNIT, FIRST CHOOSING THE CONFIGURATION THAT FITS YOUR ROOM,
LEFT OR RIGHT
SEE FIG. 13, IF LEFT GO TO STEP #3 OR RIGHT GO TO STEP #2
2.- CHANGE DOOR THAT IS FACTORY INSTALLED IN LEFT SIDE TO THE RIGHT SIDE, USING A PHILLIPS SCREWDRIVER
(NOT INCLUDED),
REMOVE SCREWS FROM CASE PORTION OF THE HINGES, KEEP THE HINGES
FOR ATTACH THE DOOR (FIG.13)
( SAVE THE SCREWS TO RE-ATTACH THE DOOR TO RIGHT SIDE)
,THEN INSTALL DOOR ON THE RIGHT SIDE.
3.-TAKE THE BACK FRAME (E), PLACE IT IN THE BACK OF STEP UNIT (A), ALIGNING THE BACK FRAME HOLES WITH THE METAL INSERTS, FASTENING WITH FOUR 1 1/2" PAN HEAD SCREWS (K), SEE FIG.14
4.- REMOVE FIRST, SECOND AND FOURTH DRAWERS FROM STEP UNIT ( A), ALIGNING HANDRAIL HOLES ( D) WITH STEP UNIT HOLES INTHE SAME SIDE DOOR, INSERTING ONE 35MM BOLT ( G) FROM OUTSIDE ON OF
HANDRAIL, ALIGNING HANDRAIL HOLE WITH BACK FRAME HOLE IN THE TOP, INSERTING ONE 100MM BOLT ( F) THEN INSERT ONE CAP NUT ( H) IN EACH BOLT, FASTEN USING ALLEN WRENCH ( I, J ), TIGHT ALL BOLTS
UNTIL SECURE, SEE FIG.14
5.- TO ATTACH TO TWIN OVER TWIN ASSEMBLY WITH STEP BUNK BED ASSEMBLY, ALIGNMENT HOLES ON BOTH SIDES, INSERT ONE 35MM BOLT IN BOTTOM HOLE AND ONE 100MM BOLT IN TOP HOLE, THEN INSERT
ONE CAP NUT IN BOTH BOLTS AND FASTEN USING ALLEN WRENCH, SEE FIG.15
6.- TO ATTACH TO TWIN OVER FULL ASSEMBLY WITH STEP BUNK BED ASSEMBLY, ALIGNMENT HOLES ON BOTH SIDES, INSERT TWO 35MM BOLTS IN BOTTOM HOLES AND ONE 100MM BOLT IN TOP HOLE, INSERT ONE
CAP NUT IN BOTH BOLTS AND FASTEN USING ALLEN WRENCH, SEE FIG.16
7.- REPLACE BACK THE DRAWERS AND MOVE STEP BUNK BED TO THE FINAL POSITION.
8.- SLIDE TRUNDLE BED (U) UNDER BOTTOM SIDE RAILS, LIKE SHOWN IN
CONFIGURATION #1
,
OPTION #2
AND
OPTION #4.
TWIN OVER FULL BUNK BED WITH EXTENTION KIT BED ASSEMBLY
USE ONE 4 PCS SLAT PACK ( 98-645 ) ON TOP SIDE RAIL AND ONE 4 PCS SLAT PACK ( 98-646 ) ON BOTTON SIDE RAIL
STEP BUNK BED UNIT ASSEMBLY
FIG. 11
FIG. B
FIG. 12
FIG. 13
FIG. 14
TWIN OVER TWIN BED
TWIN OVER FULL BED
STEP UNIT
FIG. 15
FIG. 16
REV 01 01/08/16 PAGE 3 OF 6 KIS01129