CanyCom CMX 227 Operator'S Manual Download

Page: 42 / 103

Operation

-34-

1. Stop the machine.
2. Move the auxiliary transmission shift lever to [H]

(high speed) or [L] (low speed) position firmly.

5347M-0402-102E

Auxiliary
Transmission
Shift Lever

•

See Specifications (page 15) for the speed

range in either gear position.

• Always stop the machine to shift gears. Shifting gears while the machine is in

motion can damage the transmission.

• Use [L] (low speed) mode when cutting (mowing). Cutting in [H] (high speed)

mode can put excessive strain and damage the cutting mechanism.

NOTE

• Always shift gears firmly. When the transmission is not firmly shifted, it may

jump out of the gear, resulting in loss of control of the machine.

Shifting

5347M-0402-121E

Parking Brake Pedal

3. Depress the parking brake pedal to stop the

machine completely.

• When the parking brake pedal is depressed,

the drive lever returns to the neutral
position.

NOTE

Summary of Contents for CMX 227








































































































Search results

Summary of Contents for CMX 227

Reviews:

Related manuals for CMX 227

Brands by name

Popular brands

CanyCom CMX 227, Operator'S Manual

Search results

Summary of Contents for CMX 227

Reviews:

Related manuals for CMX 227

Brands by name

Popular brands