manualshive.com logo in svg

CanyCom CMX 227, Operator'S Manual, Page: 84 / 103

Share
Download
CanyCom CMX 227 Operator'S Manual Download Page 84

Maintenance

-76-

5

Less than 5mm

Lining

Lining

Lining Groove

Backing Plate

5347M-0508-032E

Mower Clutch Lever: [ON]

Inspecting

1.  Start the engine.
2.  Turn the throttle lever to [      ] (fast) to raise the engine speed.
3.  Move the cutting height adjust lever to [150] for CMX227 and CM226.
4.  Move the mower clutch lever to [ON] to run the mower.
5.  Move the mower clutch lever to [OFF] to observe if the mower stops. If it does not stop 

(if it keeps turning by inertia), adjust the mower brake. To see if the mower is running or 
not, observe the rotating sound of the mower, or open the engine hood to observe the 
rotation of the mower V-belt. Avoid observing inside the cutting blade shield directly.   

4.  If the lining is in contact with the lining 

groove, or the gap between the backing plate 
and the pulley is greater than 5mm, adjust 
the turnbuckle.

Lock Nut

Turnbuckle

5347M-0508-040E

1.  Remove the engine hood, rear cover, and 

bumper.

2.  Move the mower clutch lever to [ON].
3.  Visually inspect if the brake lining is not in 

contact with the lining groove on the pulley. 
Also inspect if the gap between the backing 
plate and the pulley is 5mm or less.

Adjusting

 • Never attempt to check the performance of the mower brake with the cutting 

blade shield open. Stones or rocks can be thrown and cause damage to 
surrounding properties or persons.

 • Inspect the mower brake whenever the performance of it seems inadequate.

 • Stop the engine when adjusting the mower brake.

Summary of Contents for CMX 227








































































































Reviews:

No comments