Canon Super G3 Fax Board-AF1 Service Manual Download Page 70

Page: 70 / 74

Chapter 6

6-2

6.2 Service Error Code

6.2.1 Service Error Code

0025-3174

T-6-2

No. T/R

Description

##100

[T]

at time of transmission, the procedural signal has been transmitted more than specified.

##101

[T/R]

the modem speed does not match that of the other party.

##102

[T]

at time of transmission, fall-back cannot be used.

##103

[R]

at time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).

##104

[T]

at time of transmission, RTN or PIN is received.

##106

[R]

at time of reception, the procedural signal is received for 6 sec while in wait for the signal.

##107

[R]

at time of reception, the transmitting party cannot use fall-back.

##109

[T]

at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is received, and the procedural signal has been sent more than
specified.

##111

[T/R]

memory error has occurred.

##114

[R]

at time of reception, RTN is transmitted.

##200

[R]

at time of reception, no image carrier is detected for 5 sec.

##201

[T/R]

DCN is received outside the normal parity procedure.

##204

[T]

DTC without transmission data is received.

##220

[T/R]

system error (main program out of control) has occurred.

##223

[T/R]

while a communication is under way, the line is cut.

##224

[T/R]

in G3 communication, an error has occurred in the procedural signal.

##226

[T/R]

the stack printer has fallen outside the RAM area.

##229

[R]

the recording unit has remained locked for 1 min.

##232

[T]

encoding error has occurred.

##237

[R]

decoding error has occurred.

##238

[R]

the print control unit is out of order.

##261

[T/R]

system error has occurred.

##280

[T]

at time of transmission, the procedural signal has been transmitted more than specified.

##281

[T]

at time of transmission, the procedural signal has been transmitted more than specified.

##282

[T]

at time of transmission, the procedural signal has been transmitted more than specified.

##283

[T]

at time of transmission, the procedural signal has been transmitted more than specified.

##284

[T]

at time of transmission, DCN is received after transmission of TCF.

##285

[T]

at time of transmission, DCN is received after transmission of EOP.

##286

[T]

at time of transmission, DCN is received after transmission of EOM.

##287

[T]

at time of transmission DCN is received after transmission of MPS.

##288

[T]

after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.

##289

[T]

after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.

##290

[T]

after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.

##670

[T]

at time of V.8 late start, the V.8 ability of DIS front the receiving party is expected to be detected, and the CI signal is expected to be
transmitted in response; however, the procedure fails to advance, and the line is released because of T1 time-out.

##671

[R]

at time of V.8 arrival, procedure fails to move to phase 2 after detection of CM signal from caller, causing T1 time-out and releasing line.

##672

[T]

at time of V.34 transmission, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release the line and
suffer T1 timeout.

##673

[R]

at time of V.34 reception, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release the line and suffer
T1 timeout.

##674

[T]

at time of V.34 transmission, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing the machine
to release the line and suffer T1 timeout.

##675

[R]

at time of V.34 reception, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing the machine to
release the line and suffer T1 timeout.

##750

[T]

at time of ECM transmission, no meaningful signal is received after transmission of PPS-NULL, causing the procedural signal to be
transmitted more than specified.

##752

[T]

at time of ECM transmission, DCN is received after transmission of PPS-NULL.

##753

[T]

at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL, or T5 time-
out (60 sec) has occurred.

##754

[T]

at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL.

##755

[T]

at time of ECM transmission, no meaningful signal is received after transmission of PPS-MPS, causing the procedural signal to be transmitted
more than specified.

##757

[T]

at time of ECM transmission, DCN is received after retransmission of PPS-MPS.

##758

[T]

at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, or T5 time-out
(60 sec) has occurred.

##759

[T]

at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS.

##760

[T]

at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOM, causing the procedural signal to be
transmitted more than specified.