Canon Satera LBP-5600 User Manual Download Page 122

Page: 122 / 154

121

Remove the tape (3 pieces) shown in the figure in order of

and

The tape to be removed in

has another tape attached to the rear end. Remove

them together.

Hold the drum cartridge by the blue tabs and shake it up and
down 10 to 12 times each as shown in the figure to evenly
distribute the developer inside the cartridge.

Hold the blue tabs of the drum cartridge.

Shake the drum cartridge up and down 10 to 12 times each as shown in the
figure.

IMPORTANT

If the developer is not distributed evenly, this may result in deterioration in print
quality. Be sure to carry out this procedure properly.

Remove this
tape together

Tabs

Summary of Contents for Satera LBP-5600



























































































































































Search results

Summary of Contents for Satera LBP-5600

Reviews:

Related manuals for Satera LBP-5600

Brands by name

Popular brands

Canon Satera LBP-5600, User Manual

Search results

Summary of Contents for Satera LBP-5600

Reviews:

Related manuals for Satera LBP-5600

Brands by name

Popular brands