error.
Faulty EEPROM
data of the print
head.
[1405]
Multiple ink tanks
of the same color
installed.
[1487] U071 More than one ink
tank of the
following color is
installed.
Replace the wrong ink tank(s) with the correct
one(s).
- Ink tank
- Logic board
Ink tank in a wrong
position.
[1680] U072 Some ink tanks are
not installed in
place.
Install the ink tank(s) in the correct position.
- Ink tank
- Logic board
Warning: The ink
absorber becomes
almost full.
[1700]
---
Contact the support
center or service
center for ink
absorber
replacement. Press
[OK] to continue
printing.
Replace the ink absorber, and reset its
counter. [See
4-5. Special Notes on Servicing,
(5) Ink absorber counter setting.
]
Pressing the OK button will exit the error, and
enable printing without replacing the ink
absorber. However, when the ink absorber
becomes full, no further printing can be
performed unless the applicable ink absorber
is replaced.
- Absorber kit
The connected
digital camera or
digital video
camera does not
support Camera
Direct Printing.
[2001]
---
Incompatible
device detected.
Remove the
device.
Remove the cable between the camera and the
machine.
- PictBridge board
- Logic board
Automatic duplex
printing cannot be
performed.
[1310]
---
This paper is not
compatible with
duplex printing.
Remove the paper
and press [OK].
The paper length is not supported for duplex
printing.
Press the OK button to eject the paper being
used at error occurrence.
Data which was to be printed on the back side
of paper at error occurrence is skipped (not
printed).
- Duplex feed roller
unit
- PE sensor board
- Logic board
The remaining ink
amount unknown
(raw ink present).
[1683] U130 (Applicable ink
tank icon)
The remaining
level of the ink
cannot be correctly
detected.
An ink tank which has once been empty is
installed. Replace the applicable ink tank with
a new one. Printing with a once-empty ink
tank can damage the machine.
To continue printing without replacing the ink
tank(s), press the Stop button for 5 sec. or
longer to disable the function to detect the
remaining ink amount. After the operation, it
is recorded in the machine EEPROM that the
function to detect the remaining ink amount
was disabled.
- Ink tank
- Spur unit
Ink tank not
recognized.
[1684] U140 The following ink
tank cannot be
recognized.
(Applicable ink
tank icon)
A non-supported ink tank (an ink tank that is
sold in a different region from where the
machine was purchased) is installed (the ink
tank LED is turned off). Install the supported
ink tanks.
- Ink tank
- Logic board
Ink tank not
recognized.
[1682] U150 The following ink
tank cannot be
recognized.
(Applicable ink
tank icon)
A hardware error occurred in an ink tank (the
ink tank LED is turned off). Replace the ink
tank(s).
- Ink tank
- Logic board
No ink (no raw
ink).
[1688] U163 The ink has run
out. Replace the
Replace the empty ink tank(s), and close the
scanning unit (cover).
- Ink tank
- Spur unit
9 / 63
Summary of Contents for PIXMA MX870 Series
