Canon PIXMA MX340 Series Simplified Service Manual Download Page 4

Page: 4 / 35

(3/37)

Error

code

U No. Message on the LCD

Solution

Parts that are likely to be

faulty

Multiple ink

cartridges of the

same color

installed.

[1487] U075 Some ink cartridges

are not installed in

place.

Replace the wrong ink

cartridge(s) with the correct

one(s). If the error is not

cleared, the ink cartridge

may be defective. Replace

the ink cartridge.

- Ink cartridge

- Carriage unit

- Logic board

Ink cartridge

hardware error

[1682] U150 The ink cartridge

cannot be recognized.

Re-set the ink cartridge(s). If

the error is not cleared, the

ink cartridge may be

defective. Replace the ink

cartridge.

- Ink cartridge

- Carriage unit

- Logic board

Ink cartridge not

recognized

[1684] U140 The ink cartridge

cannot be recognized.

A non-supported ink

cartridge is installed. Install

the supported ink cartridge.

- Ink cartridge

- Carriage unit

- Logic board

The remaining ink

amount unknown.

[1686] U162 Ink may have run out.

Replacing the ink

cartridge is

recommended.

Replace the applicable ink

cartridge with a new one.

Printing without replacing

the ink cartridge can

damage the printer.

To continue printing without

replacing the ink

cartridge(s), press the Stop

button for 5 sec. or longer to

disable the function to detect

the remaining ink amount.

After the operation, it is

recorded in the printer

EEPROM that the function

to detect the remaining ink

amount was disabled.

- Ink cartridge

- Logic board

Ink cartridge not

installed properly.

[1687] U053 The ink cartridge

cannot be recognized.

Re-set the ink cartridge. If

the error is not cleared, the

ink cartridge may be

defective. Replace the ink

cartridge.

- Ink cartridge

- Carriage unit

- Logic board

Summary of Contents for PIXMA MX340 Series




































Search results

Summary of Contents for PIXMA MX340 Series

Reviews:

Related manuals for PIXMA MX340 Series

Brands by name

Popular brands

Canon PIXMA MX340 Series, Simplified Service Manual

Search results

Summary of Contents for PIXMA MX340 Series

Reviews:

Related manuals for PIXMA MX340 Series

Brands by name

Popular brands