Canon Paper Deck Unit-F1 Service Manual Download Page 11

Page: 11 / 112

Specifications

Item

Specifications

Remarks

Pickup method

Retard separation

Center reference

Paper accommoda-
tion

Front loading

Paper type

Thin paper (52 to 63g/m

), Plain paper (64 to105 g/m

), Heavy paper

(106 to 256g/m

), Color paper, Recycled paper, Bond paper, Pre-

punched paper, Letterhead

Transfer from the host machine

Paper size

A4, B5, LTR

Cross feed only

Paper weight

52g/ m

to 256g/ m

Transfer from the host machine

Stacking height

297mm (height to bottom of arrow on stack limit label)

Stacking capacity

Approx. 2700 sheets (equivalent of 80 g/m

)

Size switching

Switches the Guide Plates and sets on the service mode

Supported paper size : A4, B5, LTR

Paper size detection None

Remaining paper lev-
el detection

Yes

Operation switch

Compartment Open Button

Display

None

Ecological consider-
ation

Paper Moisture Adjusting Heater (option)

Dimensions

(W) 344.0mm × (D) 630.0mm × (H) 440.2mm

Weight

Approximately 31 kg

Power supply

None (DC24V/12V supplied from the host machine)

1. Product Overview

Summary of Contents for Paper Deck Unit-F1
















































































































Search results

Summary of Contents for Paper Deck Unit-F1

Reviews:

Related manuals for Paper Deck Unit-F1

Brands by name

Popular brands

Canon Paper Deck Unit-F1, Service Manual

Search results

Summary of Contents for Paper Deck Unit-F1

Reviews:

Related manuals for Paper Deck Unit-F1

Brands by name

Popular brands