Canon Paper Deck Unit-F1 Service Manual Download Page 76

Page: 76 / 112

11. Check that the position between the Pre-Separation Plate[1] and the Lifter Plate[2] is same.

NOTE:

Put a sheet of paper on Deck Lifter[2].
Move it to feeding direction and check if it does not move upward or downward by Pre-Separation Plate.

[2]

[1]

Compartment

■ Actions at Replacement

“Removing the Compartment ” on page 43

■ Actions after Replacement

1. Adjusting the Pre-Separation Plate.

“Pre-Separation Plate Adjustment” on page 64

Deck Driver PCB

■ Actions at Replacement

“Removing the Deck Driver PCB ” on page 60

■ Actions after Replacement

● Setting of Paper Deck paper size

1. Remove all sheets of paper from the Compartment.

5. Adjustment

Summary of Contents for Paper Deck Unit-F1
















































































































Search results

Summary of Contents for Paper Deck Unit-F1

Reviews:

Related manuals for Paper Deck Unit-F1

Brands by name

Popular brands

Canon Paper Deck Unit-F1, Service Manual

Search results

Summary of Contents for Paper Deck Unit-F1

Reviews:

Related manuals for Paper Deck Unit-F1

Brands by name

Popular brands