manualshive.com logo in svg

Canon LBP-3260, Service Manual

The Canon LBP-3260 is a high-performance laser printer designed for professional use. If you're looking for a comprehensive parts catalog and manual to maintain or repair this device, you can download them for free from our website. Get all the vital information you need to optimize your printer's performance at manualshive.com.

Share
Download
background image

B. Control Panel
1. Outline

The control panel contains a LCD (20 characters x 2 lines), 9 switches, and 7 LEDs.

The control panel is connected to the video controller PCB and has the functions listed below.

a. Displays status and error messages in the LCD.
b. Displays operation condition with the LED.
c.

Changes Menus and values with the switches.

2. Operation

The LCD and LEDs on the control panel are controlled by the signals output from the video con-
troller.  The signals generated by the switches on the panel are input to the video controller.

Figure 2-6-3

2 - 65

CHAPTER 2

nFP CLK

J6-C13

J3-3

nFP CS

J3-4

J3-5

J3-6

LEDs

LCD

CPU

Switches

IC10

Video controller PCB

AIR

nFP DI

nFP OD

J6-A14

J6-C14

J6-B14

DC controller PCB

Control panel

Beeper

Summary of Contents for LBP-3260











































































































































































































































Reviews:

No comments

Related manuals for LBP-3260

NEC 870 - SuperScript B/W Laser Printer Network Quickstart preview
870 - SuperScript B/W Laser Printer
Brand: NEC Pages: 8
Xerox 4050 Operator'S Manual preview
4050
Brand: Xerox Pages: 168
Xerox 4050 Reference Manual preview
4050
Brand: Xerox Pages: 36
Xerox 4050 Installation Planning preview
4050
Brand: Xerox Pages: 64
Xerox 4050 Maintenance Manual preview
4050
Brand: Xerox Pages: 54
Xerox 4050 Quick Reference Card preview
4050
Brand: Xerox Pages: 2
Xerox 4050 Message Manual preview
4050
Brand: Xerox Pages: 115
DataCard SD160 User Manual preview
SD160
Brand: DataCard Pages: 78
DataCard SP75 Plus Quick Install Manual preview
SP75 Plus
Brand: DataCard Pages: 8
DataCard CR805 User Manual preview
CR805
Brand: DataCard Pages: 136
DataCard CE840 Quick Install Manual preview
CE840
Brand: DataCard Pages: 22
DataCard CD820 Quick Install Manual preview
CD820
Brand: DataCard Pages: 16
DataCard SD260 Installation And User Manual preview
SD260
Brand: DataCard Pages: 216
DataCard CD800 Product Manual preview
CD800
Brand: DataCard Pages: 19
DataCard SP55 Plus Supplementary Manual preview
SP55 Plus
Brand: DataCard Pages: 2
DataCard SP55 Plus Printer Manual preview
SP55 Plus
Brand: DataCard Pages: 30
DataCard RP90 Brochure & Specs preview
RP90
Brand: DataCard Pages: 2
DataCard SP25 Plus Brochure & Specs preview
SP25 Plus
Brand: DataCard Pages: 4

Brands by name

Popular brands

Load more brands