Canon LBP-3260 Service Manual Download Page 115

Page: 115 / 234

4. Rear cover

1) Open the upper cover.
2) Open the pick-up unit door.
3) Remove the 2 screws, unhook the claw,

and then remove the right rear cover.

➀

Screws

➁

Claw

➂

Right rear cover

Figure 3-2-10

4) Remove the 6 screws and then the rear

cover.

➀

Screws

➁

Rear cover

Figure 3-2-11

5. Delivery cover unit

1) Open the delivery cover unit.
2) Remove the 2 rods that hold the delivery

cover unit to the printer.

3) Lifting up the delivery cover unit slight-

ly, remove the right and then the left
side of the unit.

➀

Delivery cover unit

➁

Rods

Figure 3-2-12

6. Multi-purpose tray

1) Open the multi-purpose tray.
2) Unhook the 2 claws that hold the multi-

purpose tray to the printer and pull out
the tray toward you.

➀

Claws

➁

Multi-purpose tray

Figure 3-2-13

3 - 5

CHAPTER 3

➀

➁

➂

➁

➀

➁

➀

➁

Summary of Contents for LBP-3260










































































































































































































































Search results

Summary of Contents for LBP-3260

Reviews:

Related manuals for LBP-3260

Brands by name

Popular brands

Canon LBP-3260, Service Manual

Search results

Summary of Contents for LBP-3260

Reviews:

Related manuals for LBP-3260

Brands by name

Popular brands