Canon LBP-3260 Service Manual Download Page 127

Page: 127 / 234

D. Pick-up/Feed/Separation Rollers

1) Pull out the upper and lower cassettes.
2) Grasp the knobs of each roller and pull

the rollers out of the printer.

➀

Pick-up roller

➁

Feed roller

➂

Separation roller

Figure 3-4-5

➀

Pick-up roller

➁

Feed roller/Separation roller

Figure 3-4-6

Note:

Be sure to replace the feed roller
and the separation roller together.

E. Registration Lower Roller

1) Remove the registration roller unit fol-

lowing steps 1-5 on Page 3-12.

2) Remove the registration clutch.
3) Remove the spring, the E-ring and the

bushing.

➀

Spring

➁

E-ring

➂

Bushing

Figure 3-4-7

4) Remove the gear, the spring, the E-ring,

the bushing, and then the registration
lower roller.

➀

Gear

➁

Spring

➂

E-ring

➃

Bushing

➄

Registration lower roller

Figure 3-4-8

3 - 17

CHAPTER 3

➀

➁

➂

➁

➂

➀

➁

➀

➁

➂

➀

➂

➄

➁

➃

Summary of Contents for LBP-3260










































































































































































































































Search results

Summary of Contents for LBP-3260

Reviews:

Related manuals for LBP-3260

Brands by name

Popular brands

Canon LBP-3260, Service Manual

Search results

Summary of Contents for LBP-3260

Reviews:

Related manuals for LBP-3260

Brands by name

Popular brands