Canon iPF9000 series, Service Manual

Page: 62 / 432

Chapter 1
1-46
[Paper Details]
[Job Management]
Setting Item Description, Instructions
(The paper type is displayed here.) [Roll DryingTime] Specify the time to wait for the ink to dry for each sheet.
[Scan Wait Time] Specify the time to wait for the ink to dry between each scan in bidirectional printing,
in consideration of how quickly the ink dries. Note that printing will take longer if
you specify a wait time.
[Feed Priority] Specify exact paper feeding, if desired. Normally, select Automatic. Choose Print
Length if you prefer to feed the paper an exact amount. However, note that choosing
Print Length may result in slight banding in the direction of Carriage scanning.
[Adjust Length] Displayed if Feed Priority is Print Length.
Adjustment relative to the amount of stretching or shrinkage of the current paper.
Enter either the adjustment results from Print Pattern or the discrepancy that you
measured (as a percentage).
For paper that tends to stretch, increase the feed amount by setting the adjustment
value . For paper that tends to shrink, decrease the feed amount by setting
the adjustment value toward -.
[Head Height] Adjust the Printhead height.
[Skew Check Lv.] If you print on Japanese paper (washi) or other handmade paper that has an irregular
width, choose Loose for a higher skew detection threshold, or choose Off to disable
skew detection. However, if paper is loaded askew when detection is Off, note that
paper jams or Platen soiling may occur.
[VacuumStrngth] Specify the level of suction that holds paper against the Platen.
[Width Detection] Make this setting when the print size is different from the media size, for example,
when you want to make a print within a frame.
When you select [OFF], the paper width is not detected.
[NearEnd RollMrgn] Specify the minimum margin at the leading edge of roll paper to ensure better
printing quality at the leading edge.
Note that if you choose 5mm, it may lower the printing quality at the leading edge
and affect feeding accuracy. The printed surface may be scratched, and ink may
adhere to the leading edge. It may also cause the Platen to become soiled.
[Cut Speed] Choose the cutting speed. If you use adhesive paper, choosing Slow helps prevent
adhesive from sticking to the cutter and keeps the cutter sharp.
[Trim Edge First] If a roll is loaded, the end of the paper will be cut.
[Cutting Mode] Specify whether or not to cut with the standard round-bladed cutter.
Choose Automatic to have the roll cut automatically after printing. If you choose
Manual, the paper will not be cut after printing. Instead, a line will be printed at the
cut position.
Choose Eject if you prefer not to have documents dropped immediately after
printing, as when waiting for ink to dry.
[Bordless Margin] Adjust the margin during borderless printing.
Choose Automatic to have the printer automatically detect the paper width and
configure the margin settings for borderless printing. If margins are mistakenly
created when Automatic is selected, choose Fixed. In this case, the paper width is
not detected automatically, and the document is printed without borders, using the
margin settings required by the printer.
[CutDustReduct.] Choose On to reduce the amount of debris generated when cutting film and similar
media by printing a line at the cut position. This option reduces the amount of debris
given off after cutting. It also helps prevent adhesive from sticking to the cutter and
keeps the cutter sharp if you use adhesive paper.
[NearEnd Sht Mrgn] Specify a margin at the leading edge of sheets to ensure better printing quality at the
leading edge.
Note that if you choose 5mm, it may lower the printing quality at the leading edge
and affect feeding accuracy. The printed surface may be scratched, and ink may
adhere to the leading edge.
[Return Defaults] Choose Yes to restore Paper Details to the factory default values.
Setting Item Description, Instructions
[Job Queue Ope.] [Job List] (Choose a print job) ]Delete] Print the job first after the
current print job is finished
printing.
[Priority] Delete the current job or
queued jobs.
[Com. BOX Ope.] [Job List] (Choose a print job) [Print] Print jobs in the Common Box.
[Delete] Delete jobs in the Common
Box.
[Print Job List] Print a list of jobs in the
Common Box.
[Psnl. BOX Ope.] [Folder List] (Enter a password if one has
been set.) [Job List]-[Print] Print jobs in Personal Boxes.
[Job List]-[Delete] Delete jobs in Personal Boxes.
[Print Job List] Print a list of jobs in Personal
Boxes.