Canon imageRUNNER ADVANCE 9070 PRO series, Service Manual Digest, Page: 471 / 874

5-243
5
COPIER> ADJUST> FEED-ADJ
ADJ-DK Write start pstn in horz scan:Deck/POD D
Lv.1 Details To adjust the image write start position in the horizontal scanning
direction when feeding paper from the Paper Deck/ POD Deck Lite
(paper width is within 320 mm.)
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Left margin becomes larger. (An image moves to the right.)
-: Left margin becomes smaller. (An image moves to the left.)
When replacing the DC Controller PCB/clearing RAM data, enter the
value of service label.
Use case When replacing the DC Controller PCB/clearing RAM data
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution If the paper width exceeds 320 mm, execute mechanical adjustment.
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
ADJ-REFE Write start pstn in horz scan: 2nd side
Lv.1 Details To adjust the image write start position on the second side in the
horizontal scanning direction.
The image write start position is set in the relative amount against
the first side regardless of the paper pickup cassette/tray/deck.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Left margin becomes larger. (An image moves to the right.)
-: Left margin becomes smaller. (An image moves to the left.)
When replacing the DC Controller PCB/clearing RAM data, enter the
value of service label.
Use case When replacing the DC Controller PCB/clearing RAM data
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
REG-THCK Rgst start timing adj: Heavy, 1/2 speed
Lv.1 Details To adjust the top margin by changing the timing to turn ON the
Registration Motor when feeding heavy paper.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Top margin becomes smaller. (An image moves upward.)
-: Top margin becomes larger. (An image moves downward.)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value -20
COPIER> ADJUST> FEED-ADJ
REG-DUP1 Rgst start timing adj: Plain, 2nd side
Lv.1 Details To adjust the top margin by changing the timing to turn ON the
Registration Motor when feeding the second side of plain paper.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Top margin becomes smaller. (An image moves upward.)
-: Top margin becomes larger. (An image moves downward.)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value -10
REG-DUP2 Rgst start timing adj: Heavy, 2nd side
Lv.1 Details To adjust the top margin by changing the timing to turn ON the
Registration Motor when feeding the second side of heavy paper.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Top margin becomes smaller. (An image moves upward.)
-: Top margin becomes larger. (An image moves downward.)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value -10
LP-FEED1 Cassette pre-rgst arch amount: Plain
Lv.1 Details To adjust the arch amount before registration when feeding plain
paper from the cassette.
As the value is incremented by 1, the pre-registration arch amount
changes by 0.1 mm.
+: Increase
-: Decrease
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0