Canon imagePROGRAF iPF8400, Service Manual

Page: 43 / 308

Chapter 1
1-29
[Set./Adj. Menu]
T-1-14
Setting Item Description/Instructions
[Test Print] [Nozzle Check] Print a nozzle check pattern.
[Status Print] Print the printer information.
[Interface Print] Print the interface settings.
[Paper Details] Prints the paper settings set with [Paper Details].
[Print Job Log] Print print job information such as paper type, size, and ink consumption. Ink consumption is
the approximate amount of ink used to print one sheet.
[Menu Map] Print the menu list.
[Adjust
Printer] [Head Posi. Adj.] The printer prints and reads a test pattern for automatic or manual adjustment of Printhead
alignment relative to the printing direction.
[Feed Priority] [Adj. Priority] [Automatic] Set the priority feed precision. Normally select [Automatic]. Select [Print Quality] to print at
high quality. Select [Print Quality] to reduce horizontal streaks. Select [Print Length] to
accurately control the feed amount. However, selecting [Print Length] may cause colors to
become slightly uneven in the carriage scan direction.
[Print Quality]
[Print Length]
[Adj. Quality] [Auto(Genuin
ePpr)]
Set when using paper described in the paper reference guide.
A pattern to adjust the paper feed amount is printed, and the feed amount is automatically
adjusted from the printed result.
[Auto(OtherPa
per)] Set when using paper not described in the paper reference guide.
A pattern to adjust the paper feed amount is printed, and the feed amount is automatically
adjusted from the printed result.
This takes longer than [Auto (GenuinePpr)] to print and consumes more ink.
[Manual] Select for paper that cannot be adjusted by [Auto(GenuinePpr)] or [Auto(OtherPaper)], such as
highly transparent paper.
Print a pattern to adjust the paper feed amount according to the type of paper.
[Adjust
Length] [AdjustmentPr
int]-[A:High]/
[B:Standard/
Draft] Print a test pattern for adjustment relative to paper stretching or shrinkage, after which you can
enter the amount of adjustment.
[Change
Settings]-
[A:High]/
[B:Standard/
Draft] Displayed when [Print Length] is selected as [Adj. Priority] for [Feed Priority].
Adjust the expansion rate of the currently loaded paper.
Enter the result adjusted with [AdjustmentPrint] or the difference with your own measurement
in %.
Increase the adjustment value to increase the feed amount for paper that tends to expand, and
reduce it for paper that tends to shrink.
[Calibration] [Auto Adjust] Choose Yes for automatic adjustment of the adjustment value after a test pattern for color
calibration is printed. The new color calibration adjustment value is applied in all print jobs.
[Calibration Log] Check the date when color calibration was executed, as well as the type of paper used, as shown
on the Display Screen.
[Use Adj. Value] Choose Disabled >OK if you prefer not to apply the color calibration adjustment value in print
jobs. The printer driver settings will be used instead.
Choose Enabled >OK to apply the color calibration adjustment value in print jobs. However,
printer driver settings are given priority.
[Set Exec. Guide] Choose On if you want to be displayed the message at the recommended timing of the
calibration.
[Return Defaults] Clear the color calibration adjustment value and the execution log.
[Maintenance] [Head Cleaning] Specify Printhead cleaning options.
Choose Head Cleaning A if printing is faint, oddly colored, or contains foreign substances.
Choose Head Cleaning B if no ink is printed at all, or if printing is not improved by Head
Cleaning A.
[Nozzle Check] Print a nozzle check pattern.
[Replace P.head] Not displayed during a warning message that the remaining Maintenance Cartridge capacity is
low.
When replacing the Printhead, choose Yes and follow the instructions on the screen.
[Repl. maint cart] When exchanging the maintenance cartridge, choose Yes and follow the instructions on the
screen.
[Repl. S. Cleaner] When replacing the Shaft Cleaner, choose Yes and follow the instructions on the screen.
[Change Cutter] When transferring the printer to another location, choose the level of transfer and follow the
instructions on the screen.