Canon FACSIMILE BASIC 2000 Service Manual Download Page 202

Page: 202 / 381

G3 FACSIMILE COMMUNICATIONS

5–60

Here, the survivor paths in any step i exist individually in each of the

respective states, and the distances (pathmetric) with receive data strings

relating to each survivor path are assumed to Mai, Mbi, Mci and Mdi. At

this time, the following operation is repeated in Vitterbi decoding.

(1) In each of states A, B, C and D of step i+1, the distance up to the

receive data of the two branches arrived at from step i is calculated.

(branchmetric)

(2) In each of the states of step i+1, the sum of branchmetric of the two

branches arrived at from step i and the distance (that is, pathmetric) up

to step i corresponding to this is calculated and compared. Whichever

of the paths smaller than the sum of the distance of these two is taken

to the survival path in step i+1. The sum of the distance in the survival

path is taken to the new pathmetric in step i+1

(3) The survival path and pathmetric in each of the states in step i+1

obtained by the above calculation result are stored.

(4) The same operation is repeated in step i+2.

Fig. 5-52 shows the flow of the above operation. In the figure, operations

in states A and B in step i+1 are shown. This update operation is called

ACS (Add-Compare-Select) operation, and the distance is successively

compared to select the survival path

Summary of Contents for FACSIMILE BASIC 2000





























































































































































































































































































































































































Search results

Summary of Contents for FACSIMILE BASIC 2000

Reviews:

Related manuals for FACSIMILE BASIC 2000

Brands by name

Popular brands

Canon FACSIMILE BASIC 2000, Service Manual

Search results

Summary of Contents for FACSIMILE BASIC 2000

Reviews:

Related manuals for FACSIMILE BASIC 2000

Brands by name

Popular brands