Canon FACSIMILE BASIC 2000 Service Manual Download Page 160

Page: 160 / 381

G3 FACSIMILE COMMUNICATIONS

5–18

Fig. 5-15 Example of Two Consecutive Scanlines

This scheme is particularly effective in coding documents containing lots

of text broadly spread vertically or horizontally (that is, documents con-

taining few shifts of changing pixels).

By the MH coding scheme, 3-bit, 4-bit and at maximum 13-bit coded data

must be used to express a single run length. However, with the MR coding

scheme, the run length can be expressed just by coded data of one bit if the

previous run length is the same as the current run length.

4.3.2 Combination of MH and MR schemes

Actually, a combination of the MH and MR coding schemes are used as

the MR coding scheme. In other words, both the MH code table and MR

code table are used for the following reason.

(1) By the MR coding scheme, coding must be started from completely

describing the initial line. Otherwise, subsequent lines cannot be

coded using the data that indicates the presence of changes.

(2) When a document is transmitted by only the MR coding scheme, the

receiving side facsimile sometimes cannot correctly decode the scan-

line due to an error occurring midway during transmission. Because of

the nature of the MR coding scheme, this transmission error will affect

to the end of the following scanlines.

(2) above is an important issue, and is a disadvantage in the MR coding

scheme. The MR coding scheme is a means for complementing this disad-

vantage. A number of scanlines in one page are combined and MH coding

is carried out on every leading scanline. MR coding is performed on subse-

quent scanlines. The combined number of scanlines is referred to as

Previous line
Present line

Summary of Contents for FACSIMILE BASIC 2000





























































































































































































































































































































































































Search results

Summary of Contents for FACSIMILE BASIC 2000

Reviews:

Related manuals for FACSIMILE BASIC 2000

Brands by name

Popular brands

Canon FACSIMILE BASIC 2000, Service Manual

Search results

Summary of Contents for FACSIMILE BASIC 2000

Reviews:

Related manuals for FACSIMILE BASIC 2000

Brands by name

Popular brands