background image

Terminating the Downrigger Cable 

Cannon Uni-Release 

 

 

The Cannon Uni-Release attaches directly to 

the downrigger weight. Attach fishing line to the 
clip at the end of the release, and then click 
through a series of increasing tension settings. 
The release can be used with any test line on salt 
or fresh water and may be adjusted from 2 to 22 
pounds of grip tension on the line. 

 

To change line release tension, turn tension 

knob to (+) to increase or (-) to decrease. Tension 
also may vary according to where the line is 
placed in the grips. Higher tension is on the line if 
it is set back toward the hinge, and lower if set 
closer to the opening. To open the release, spread 
the release arms with thumb and forefinger 
applying pressure to the sides. 

Rubber Cushion 

Cable 

Snap & 
Swivel 

Tip: A set of pliers with wire cutters is 
recommended for this part of setup. 

 

Examine the top of the terminator and note the 
order shown in the detail to run cable. 

Unwind about 2 feet of cable 
and thread the cable through 
the rubber cushion.  

Lead cable into 
HOLE A.  
Pull six inches of 
cable through. 
Thread cable 
through swivel, 
then up into 
bottom of the 
terminator.  

 

Lead cable out of 
HOLE B and into 
HOLE C. Push the 
cable until its end 
touches the inside 
of the terminator 
hook. 

HOLE A 

Swivel  

TIP:  Use only straight cable, not kinked. 

Tighten cable 
by squeezing 
terminator 
until it snaps 
shut. Then 
pull at top and 
bottom until 
drawn tight. 
Make sure  
that the cable 
threads the 
hook. 

Slide the cushion over the top of the 

terminator and give it a test pull. 

 

 

The cable is set to attach a Cannon 

Trolling Weight.  

 

Close 

Open 

Tension 
Adjust 

Fishing Line 

Gripper 

Pads 

Open 

 

 

TERMIN

ATOR &

 LINE RELEASE 

Attach to terminator. 

CABLE IN 

CABLE IN 

CABLE OUT 

AnglingOutpost.com

1-888-356-5022

AnglingOutpost.com

1-888-356-5022

Summary of Contents for Digi-Troll IV

























Reviews: