background image

24

 

All CANNON Downriggers are covered by US Pat.D-269, 992.  Copyright 2006 Johnson Outdoors, Inc. All rights reserved.  Conforms to 89/336/

EEC (EMC) under standards EN 55022A, EN 50082-2 since 1996 LN V9677264 

 

WARNING: 

This product contains chemical(s) known to the state of California to cause cancer and/or reproductive toxicity.  

 

Form No. 3397100 Rev C 

Johnson Outdoors, Inc. / Cannon Division 

121 Power Drive, Mankato, MN 56001 

1-800-227-6433 

© 2008 Johnson Outdoors, Inc. All rights reserved. 

To download product manuals or purchase Cannon products from an authorized dealer, please visit our web page at 

www.cannondownriggers.com

 

ENVIRONMENTAL COMPLIANCE STATEMENT: 

It is the intention of Johnson Outdoors Inc. to be a responsible corporate citizen, operating in compliance with known and applicable 

environmental regulations, and a good neighbor in the communities where we make or sell our products. 

 
WEEE Directive: 

 

EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers, and manu-

facturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electronics to take responsibility 
for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle. 
 

WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE de-

signed and intended as fixed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In some European Union 
member states, these vehicles are considered outside of the scope of the Directive, and EEE for those applications can be considered excluded 
from the WEEE Directive requirement.   
 

This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of with other household refuse. 

It must be disposed of and collected for recycling and recovery of waste EEE. 
Johnson Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply in the collec-
tion, treatment, recovery, and environmentally sound disposal of those products; however, these requirement do vary within Euro-
pean Union member states. For more information about where you should dispose of your waste equipment for recycling and 
recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your prod-
uct was purchased. 

AnglingOutpost.com

1-888-356-5022

AnglingOutpost.com

1-888-356-5022

Summary of Contents for Digi-Troll IV

























Reviews: