background image

4

 

 

www.cannondownriggers.com 

Product W

a

rra
nt

y

 

CANNON LIMITED WARRANTY 

 

Johnson Outdoors Marine Electronics, Inc. warrants to the original 

purchaser that if the accompanying product (see exclusions below) 
proves to be defective in material or workmanship within the following 
warranty periods, Johnson Outdoors Marine Electronics, Inc. will, at its 
option, either repair or replace same without charge (but no cash 
refunds will be made): 

1) The boom, motor, and reels, plus all composite parts, including 

but not limited to frames and bases, will be free from defects in 
materials and workmanship, subject to normal wear and tear, 
for the original purchaser's lifetime. 

 2) All other items will have 1-year limited warranties from the 

date of original retail purchase, except THE FOLLOWING 
ITEMS THAT HAVE NO WARRANTY WHATSOEVER: boot 
covers, clothing, Dacron line, rubber bands, swivel lock pin, 
weights, and wire cable.  

  This limited warranty may be enforced only by the original 

purchaser; all subsequent purchasers acquire the product "as 
is" without any benefit of this limited warranty. Repair or 
replacement of the product as set forth in this limited warranty 
shall be the original purchaser’s sole and exclusive remedy 
and Johnson Outdoors Marine Electronics, Inc.’ sole and 
exclusive liability for breach of this warranty. 

 

EXCLUSIONS 

 This warranty does not apply in the following circumstances: 
 

• 

When the product has been connected, installed, combined, 
altered, adjusted, serviced, repaired, or handled in a manner 
other than according to the instructions furnished with the 
product 

• 

When the motor housing is opened by anyone other than 
Cannon

® 

Authorized service repair personnel. 

• 

When any defect, problem, loss, or damage has resulted from 
any accident, misuse, negligence, carelessness, or abnormal 
use, or from any failure to provide reasonable and necessary 
maintenance in accordance with the instructions of the owner's 
manual 

 

LIMITATION AND EXCLUSION OF IMPLIED WARRANTIES AND 
CERTAIN DAMAGES 

 
 

THERE ARE NO EXPRESS WARRANTIES OTHER THAN 

THESE LIMITED WARRANTIES. JOHNSON OUTDOORS MARINE 
ELECTRONICS, INC. DISCLAIMS LIABILITY FOR INCIDENTAL AND 
CONSEQUENTIAL DAMAGES, AND IN NO EVENT SHALL ANY 
IMPLIED WARRANTIES (EXCEPT ON THE BOOM, MOTOR, 
REELS, AND ALL COMPOSITE PARTS), INCLUDING ANY IMPLIED 
WARRANTY OF MERCHANTABILITY OR FITNESS FOR 
PARTICULAR PURPOSE, EXTEND BEYOND ONE YEAR FROM 
THE DATE OF PURCHASE (AND IN THE CASE OF THE BOOT 
COVERS, CLOTHING, DACRON LINE, RUBBER BANDS, SWIVEL 
LOCK PIN, WEIGHTS, AND WIRE CABLE, JOHNSON OUTDOORS 
MARINE ELECTRONICS, INC. DISCLAIMS ALL IMPLIED 
WARRANTIES). THIS WRITING CONSTITUTES THE ENTIRE 
AGREEMENT OF THE PARTIES WITH RESPECT TO THE 
SUBJECT MATTER HEREOF; NO WAIVER OR AMENDMENT 
SHALL BE VALID UNLESS IN WRITING SIGNED BY JOHNSON 
OUTDOORS MARINE ELECTRONICS, INC. 
 
Some states do not allow limitations on how long an implied warranty 
lasts or the exclusion or limitation of consequential damages, so the 
above limitation or exclusion may not apply to you. This warranty 
gives you specific legal rights, and you may also have other rights that 
vary from state to state. 

CANNON

® 

SERVICE POLICY 

 

AFTER THE APPLICABLE WARRANTY PERIOD 

 
 

After the applicable warranty period, or, if one of the above exclu-

sions applies, Cannon products will be repaired for a charge of parts 
plus labor. All factory repairs, after the applicable warranty period, 
carry a 90-Day Limited Warranty, subject to the exclusions and limita-
tions stated above. 
 

TO ENFORCE WARRANTY OR TO  
OBTAIN REPAIRS AFTER WARRANTY 

 
  To obtain warranty service in the U.S., the downrigger or part be-
lieved to be defective and the proof of original purchase (including the 
date of purchase) must be presented to a Cannon Authorized Service 
Center or to Cannon’s factory service center in Mankato, MN. Except 
as noted below, any charges incurred for service calls, transportation 
or shipping/freight to/from the Cannon Authorized Service Center or 
Cannon’s factory, labor to haul out, remove, re-install or re-rig prod-
ucts for warranty service, or any similar items are the sole and exclu-
sive responsibility of the purchaser. Downriggers purchased outside of 
the U.S. (or parts of such downriggers) must be returned prepaid with 
proof of purchase (including the date of purchase and serial number) 
to any Authorized Cannon Service Center in the country of purchase. 
Warranty service can be arranged by contacting a Cannon Authorized 
Service Center listed on the enclosed sheet, or by contacting the fac-
tory at 1-800-227-6433 or Fax 1-800-527-4464. If the necessary re-
pairs are covered by the warranty, we will pay the return shipping 
charges to any destination within the United States. 
 

DO NOT 

return your Cannon

 

downrigger or parts to your retailer. Your 

retailer is not authorized to repair or replace them. 
 
 

Major parts, such as the motor and main frame, must be returned 

to Johnson Outdoors Marine Electronics, Inc. in Mankato, Minnesota, 
or a Cannon

 

Authorized Service Center, for repair or replacement. To 

reduce shipping costs, we suggest removal of loose parts such as the 
boom and rod holders. Small parts that can be easily removed such 
as the handle and/or the counter, may be removed from the downrig-
ger and returned for repair or replacement. 
 

Retain your sales receipt! Proof of purchase must accompany 
product when returned. 

 

Return Address:

  

Cannon 

 121 

Power 

Drive 

 

Mankato, MN 56001 

 

FOR YOUR INFORMATION: 
 

 
 _______________________Serial 

No. 

 
 
 __________________Date 

Purchased 

 
 
 

____________Store Where Purchased 

 
RETAIN THIS SECTION FOR YOUR RECORDS 

Summary of Contents for DIGI-TROLL 10









































Reviews: