manualshive.com logo in svg

C&K systems Sierra S5030, Technical Manual

Share
Download
C&K systems Sierra S5030 Technical Manual Download Page 9

1

Overview

5

Understanding the Lights (LEDs)

Zone  LEDs

If off

, the zone is normal.

If on

, a sensor in the zone detects a

problem. (The zone is said to be faulted.)

If blinking fast

, a sensor in the zone is

signaling an alarm, or the zone's sensor
has been tampered with.

If blinking slowly

, the zone is bypassed.

If blinking unevenly

, a sensor in the zone

may need service. (This is called a
trouble zone.)

Power LED

If on

, the system's power

supply is normal.

If off

, the keypad is drawing

power from the battery.

If blinking slowly

, the battery is

low (call for service).

Service LED

If on

, a system

component is
malfunctioning and
may need service.

If off

, all system

components are
normal.

Arm LED

If on

, the system is armed.

If off

, the system is disarmed.

If blinking fast,

 the system is about

to arm; leave the building.

If blinking slowly

, you have time to

cancel an alarm, before it
sounds.

If blinking unevenly

, system is

armed with instant arming.

Your keypad has a number of LEDs that summarize the status of
your security system. Each LED can convey several different mes-
sages by being on, off, or blinking. The illustration shows what
messages the lights communicate.

LED Blink Rates

Slow: light blinks twice every three seconds
Fast: light blinks three times every two seconds
Uneven: light blinks for three seconds, then pauses for two seconds

Ready LED

If on

, the system can

be armed.

If off

, a problem exists

which may prevent
arming.

If all of the
LEDs are
blinking,
enter your
user code.

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for Sierra S5030





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands