C&K systems Sierra S5030 Technical Manual Download Page 6 | Manualshive

Page: 6 / 68

background image

1

Overview

2

How Your Security System Works

When an intruder enters the building, a detection device is trig-
gered. The device sends a message to the control panel. The
device may have LEDs (lights) that flash.

The control panel responds by sounding the alarm. (Alarm sounds
vary. If your system is programmed for silent alarms, no bells
sound.) A message is sent to the keypad and, if connected, to
the monitoring station.

The keypad blinks its LEDs. Personnel at the monitoring station
confirm the alarm and respond accordingly.

Some alarms can be canceled before the siren sounds and the
monitoring station is notified. See Section 4 for more informa-
tion.

Intruder

Sensor

Triggers Alarm

CONTROL

PANEL

Siren

Sounds Alarm

Keypad

Issues Warnings

Monitoring

Station Is

Notified

Technical Manuals Online! - http://www.tech-man.com

«
...
4
5
6
7
8
...
»

Summary of Contents for Sierra S5030





































































Reviews:

No comments

Related manuals for Sierra S5030

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 16

Brand: HAICAM Pages: 2

Gemini GEM-X255

Brand: NAPCO Pages: 40

Brand: NAPCO Pages: 16

Brand: NAPCO Pages: 6

Brand: Mace Pages: 1

Pure Link 1300 Series

Brand: lancer Pages: 20

Brand: Kayoba Pages: 44

Brand: Idis Pages: 19

TECHNOMIG 210 DUAL SYNERGIC

Brand: Telwin Pages: 176

ELI-SIP-PPTZ-21-10X

Brand: e-Line Technology Pages: 50

Brand: Velleman Pages: 12

Brand: Neilsen Pages: 9

Brand: Daewoo Pages: 20

Brand: Holzmann Pages: 23

DWC-B1362TIR650

Brand: DW Pages: 20

Brand: ewoo Pages: 85

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands