background image

 

 

Using the Lantronix WiBox with the CR800 or CR1000

 

Display key (N) ? Y 
Key type 0=hex, 1=passphrase (0) ? 1 
Enter Key: Abcdefg12345 
It is strongly recommended to use a passphrase of 20 chars or more! 

Encryption: 0=CCMP, 1=CCMP+TKIP, 2=CCMP+WEP, 3=TKIP, 4=TKIP+WEP (3) ? 1 
TX Data rate: 0=fixed, 1=auto fallback (1) ? 
TX Data rate: 0=1, 1=2, 2=5.5, 3=11, 4=18, 5=24, 6=36, 7=54 Mbps (7) ? 
Minimum TX Data rate: 0=1, 1=2, 2=5.5, 3=11, 4=18, 5=24, 6=36, 7=54 Mbps (0)? 
Enable power management (N) ? 
Enable Soft AP Roaming (N) ? 
Max failed packets (6 - 64; 255=disable): (6) ? 

Change Setup: 
 

0 Server 

 

1 Channel 1 

 

2 Channel 2 

 

4 WLAN 

 

5 Expert 

 

6 Security 

 

7 Defaults 

 

8 Exit without save 

 

9 Save and exit  

 

Your choice ? 1  

Baudrate (9600) ? 115200 
I/F Mode (4C) ? 
Flow (00) ? 
Port No (10001) ? 
ConnectMode (C0) ? 
Send '+++' in Modem Mode (Y) ? 
Show IP addr after 'RING' (Y) ? 
Auto increment source port (N) ? 
Remote IP Address : (000) .(000) .(000) .(000) 
Remote Port (0) ? 
DisConnMode (00) ? 
FlushMode (00) ? 
DisConnTime (00:00) ?: 
SendChar 1 (00) ? 
SendChar 2 (00) ? 

Change Setup: 
 

0 Server 

 

1 Channel 1 

 

2 Channel 2 

 

4 WLAN 

 

5 Expert 

 

6 Security 

 

7 Defaults 

 

8 Exit without save 

 

9 Save and exit  

 

Your choice ? 9  

Parameters stored ... 

 

 

Summary of Contents for Lantronix WiBox


















Reviews: