background image

3

Welcome to the Camso family

Thank you for choosing our Track Systems to make your ride a new beast.
Our products are designed to take you further and help you work harder in all terrain, whether you’re hunting,

ice fishing, caring for your land, reaching your remote cabin, or taking on any outdoor adventure. No matter

where or in what conditions, get there and back safely with your Camso track systems.
Ready to benefit from optimal traction, mobility, stability, and flotation?
Let’s go make tracks!

REMARKS / CONSTRAINTS

Track  systems  can  create  constraints  during
installation  and/or  use.  Minor  interference  may
result  and  modification  to  the  vehicle  may  be
necessary.

On this vehicle model, the track system’s design
results  in  the  following  constraints  and  related
recommendations:

• Light  interference  and  minor  modifications

possible.

• Temporary vehicule modifications

PRE-INSTALLATION  CHECK  OF  TRACK
SYSTEM SPROCKET RATIO

SYMBOLS AND SIGNAL WORDS

This  document  uses  the  following  signal  words

and symbols to emphasize particular information:

CAUTION:  Indicates  a  potentially  hazardous

situation  which,  if  not  avoided,  may  result  in

damage to vehicle and Track System components.

NOTE: Indicates supplementary information.

WARNINGS

Scan the QR code to the right and 

access the 

Fitment Guide

 to validate 

the number of teeth on front and rear 

sprockets specific to your vehicle 

model.

WARNING

Indicates  a  potentially  hazardous  situation

which,  if  not  avoided,  could  result  in  death  or

serious injury.

 

WARNING

Install  Track  System  at  an  authorized  Camso

dealer. Refer to the 

Warranty 

section in the 

User

manual

.

WARNING

Wear protective gloves and goggles.

WARNING

Immobilize  vehicle  on  a  flat  and  level  surface,

shift transmission into 

Park

 and turn engine off.

WARNING

Raise and install vehicle on secure supports (or

lifting device).

WARNING

Ensure that the vehicle is immobilized and safe

to work on.

WARNING

Beware of hot surfaces that may cause injury.

WARNING

Moving parts - Hands or fingers caught between

moving parts of the equipment present a danger

to life or limb.

WARNING

Do  not  place  any  part  of  your  body  under  the

vehicle  unless  it  is  securely  placed  on

appropriate stands. Severe injuries could occur

if the vehicle collapses or moves. Do not use a

lifting device as a secure stand.

Summary of Contents for ARGO 5000-38-1094-MAN

























Reviews: