background image

 

 

CAMPO EQUIPMENT CO. LTD. (ECOBLAZE) 

6 Carson Court, Brampton, ON, CANADA, L6T 4P8 

Tel: (905) 793-2525 | Fax: (905) 793-8768 

www.campoequipment.com

  

pg. 3

 

FOREWORD 

  

This Operator's Service Manual is intended to 

familiarize  you  with  the  operation  of  and 
necessary service information for the

  

BLAZE DF1600

 gas fired model.  Please read 

this  manual  thoroughly  before  operating  the 
Blaze DF1600.  
  

This  manual  uses  the  words 

WARNING

CAUTION

,  and 

NOTE

  to  emphasize  certain 

information.   

WARNING

  identifies  personal 

safety related information; therefore, be sure to 
read  the  directive  because  it  deals  with  the 
possibility  of  personal  injury.   

CAUTION

 

identifies heater-related information; therefore, 
be sure to read the directive because it deals 
with the possibility of damaging part or parts of 
the 

Blaze 

DF1600. 

NOTE

 

identifies 

supplementary information worthy of attention.  
  

This  manual  covers  operating  instructions, 

operator  related  maintenance  instructions, 
specifications,  and  service  information.    This 
manual should be considered a permanent part 
of the Blaze DF1600 and must remain with the 
heater at the time of resale. If additional service 
information is desired, either contact your local 
dealer or write or phone:  
  

CAMPO EQUIPMENT CO.LTD. 

(ECOBLAZE)  

6 Carson Court 

Brampton, ON,  

Canada L6T 4P8  

Tel: (905)793-2525  

Fax: (905) 793-8768  

www.campoequipment.com  

 

LIMITED WARRANTY  

 

 

Campo  Equipment  CO.LTD  and  accessories 

are  warranted  to  the  original  retail  purchaser.  
No warranty is transferable to any subsequent 
owner.  The  warranty  period  is  one  year  from 
the date of purchase. The warranty covers  all 
defects in material and workmanship insofar as 
they  are  of 

Campo  Equipment  CO.  LTD

manufacture.    This  warranty  is  limited  to  the 

furnishing  of  new  parts  only,  in  the  event  the 
original  part  is  determined  to  be  defective  by 

Campo Equipment CO.LTD.

 

The warranty does not include transportation 
costs, labour for inspecting, repairing, or 
replacing original parts, or consequential 
damages.  It also does not cover any damage 
because of negligence, accident, misuse, or 
abuse.  

Campo Equipment CO.LTD

  shall not 

be liable for delays caused by defects, for 
consequential damages, or for any other 
damages, charges, or expenses of any nature.  
All parts not manufactured by 

Campo 

Equipment CO.LTD.

 are warranted insofar as 

warranted by the manufacturer of such parts.  

 

SPECIFICATIONS

  

 

 

Model Number ..................................DF1600      
Width.......................................31.5" (80.01cm) 

Length......................................... 92" (233.68 cm)

 

Height ......................................58.67"(149.02cm)

 

Weight ..........................992.00 lbs. (449.96Kg)  

Supply panel................23.125

”x27” (Rectangular)

 

Blower Motor ........................3.5Hp (2.57 Kw)  

Heated Air Output.......9452 CFM (315.42 m³/min) 

Manifold Pressure” W.C….….2.5” LP and 5.6” NG 
High  pressure  switch  to  be  adjusted  for  manifold 

pressure 

Minimum/Maximum Supply Pressure “W.C…10/14 

Pilot Pressure ......................

...............3.6” W.C 

Maximum BTU Input ........................ 1,600,000  

Kcal/h .................................................403193.2

 

   

Minimum BTU Input LP............................326289 

Kcal/h ...................................................822223  

Minimum BTU Input NG...........................324538 

Kcal/h .....................................................81782 
 
Required Voltage: 
208v to 240v 1Phase or 3 phase  

Full Load Amps: 
1 Phase 14 amps @ 230v 
3Phase 8 amps @230v 

This  unit  is  equipped  with  constant  voltage 
system.  It  is  activated  when  voltage  is  lower 
than 208v or higher than 240v. 
 

Minimum 4 X 420lb cylinders are to be used. 

Summary of Contents for ECOBlaze DF1600




















Reviews: