Campbell SDM-SIO4 Instruction Manual Download | Manualshive

Page: 36 / 82

background image

Section 5. Programming the Datalogger

5-4

Port 4 data available
| Port 3 data available
| | Port 2 data available
| | | Port 1 data available
| | | |

x x x x

If any of these four digits is greater than zero then data is available.

Values per repetition = 1

5.2.3 Command 2: Signatures

This command gets the SDM-SIO4 EPROM signature and the string memory
area signature; the two values are written into consecutive input locations. If the
signatures are zero then there could be corrupt data.

Values per repetition = 2

5.2.4 Command 3: Flush all Receive Buffers

Stored data in the SDM-SIO4 relevant to the port is also erased with this
command.

Values per repetition = 0

5.2.5 Command 4: Send Data to Datalogger

This command requests the SDM-SIO4 to send the specified (values/reps)
number of floating point values it has already received from the RS232 device
(relevant to the port specified) into input locations. -99999 is stored if no value
is available.

For example, this command could be used to get data converted using input
filter strings of type d, D, f, F, pn, bn, u[ ], vn[ ], wn[ ] and B[n,n..] – see
Section 3.

5.2.6 Command 5: Status

This command returns the SDM-SIO4 general status, lithium battery level,
errors and data available flags. The data is supplied as two floating point
values. First value:

Number of watch dog resets
| | Number of invalid commands executed
| | | Lithium battery level
| | | |

x x x x

Number of watch dog resets:

This is a count from 0 to 99. This indicates that

there has been some hardware or software failure, or can be caused by the
datalogger transmitting the correct address but not transmitting any commands.

«
...
34
35
36
37
38
...
»

Summary of Contents for SDM-SIO4



















































































Reviews:

No comments

Related manuals for SDM-SIO4

Brand: 2easy Pages: 12

Brand: 2easy Pages: 30

Brand: E-Mu Pages: 72

Brand: E-Mu Pages: 44

Brand: stellar labs Pages: 52

Brand: The Handy Pages: 4

Brand: Aiphone Pages: 4

Brand: AMX Pages: 2

Brand: M-system Pages: 9

Ezi-IO EtherCAT DA

Brand: Fastech Pages: 52

Aqua-Pure 3MFF100

Brand: 3M Pages: 8

Brand: Ravaglioli Pages: 72

Brand: MPMan Pages: 32

Brand: Crosby Pages: 8

Brand: hager Pages: 62

Brand: First Power Pages: 16

Brand: NAIM Pages: 51

Brand: Bishamon Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands