background image

6

Operating Instructions

www.chpower.com

Limited Warranty

1 .  DURATION: From the date of purchase by the original purchaser as follows: one (1) year .
2 .  WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, 

Ohio, 45030, Telephone: (800) 543-6400 .

3 .   WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell 

Hausfeld product . 

4 .   WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This Campbell Hausfeld impact wrench . 
5 .   WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the 

duration of the warranty period with the exceptions below .

6 .   WHAT IS NOT COVERED UNDER THIS WARRANTY:

A .  Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM 

THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION . If this product is used for commercial, industrial 
or rental purposes, the warranty will apply for ninety (90) days from the date of purchase . Some States do not allow 
limitation on how long an implied warranty lasts, so the above limitations may not apply to you .

B .  ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, 

FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT . Some States do not allow the exclusion or 
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you .

C .  Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with 

instructions provided in the owner’s manual(s) supplied with product . Accident, purchaser’s abuse, neglect or failure to 
operate products in accordance with instructions shall also include the removal or alteration of any safety devices . If 
such safety devices are removed or altered, this warranty is void .

D .  Normal adjustments which are explained in the owner’s manual(s) provided with the product .
E .  Items or service that are normally required to maintain the product, e .g . o-rings, springs, gaskets, packings or seals, 

lubricants, motor vanes, impact mechanism, or any other expendable part not specifically listed . These items will only 
be covered for ninety (90) days from date of original purchase . Underlined items are warranted for defects in material 
and workmanship only .

7 .  RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or 

components which are defective, have malfunctioned and/or failed to conform within the duration of the specific 
warranty period . 

8 .  RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A .  Provide dated proof of purchase and maintenance records .
B .   Call Campbell Hausfeld (800-543-6400) to obtain your warranty service options . Freight costs must be borne by the 

purchaser .

C .  Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s) . 

9 .  WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be 

scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of 
replacement parts .

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights . You may also 
have other rights which vary from state to state or country to country .

Summary of Contents for TL140289













Reviews: