Campbell Hausfeld TL140289 User Manual Download

Page: 3 / 12

TL140289

www.chpower.com

Operation (Continued)

SPEED ADJUSTMENT

The impact wrench should never
be used to set torque . Use a torque
wrench to set the torque . All models
are equipped with regulators for speed
adjustment (Refer to parts manual for
tool features) .
To remove lugs or bolts, set the
regulator to the maximum setting .
When installing, always use a torque
wrench to attain the proper torque of
the lugs or bolts .

When reassembling

be careful not to

overtighten. Bolts may fail or cause a
hazardous condition. Be sure to set the
regulator to the minimum setting then
use a torque wrench to set torque.

AIR TOOL SET-UP
NOTE

: It is not recommended to install

a quick coupler between the tool and
the whip hose .
Using fittings or air hoses which are
too small can create a pressure drop
and reduce the power of the tool . For
3/8, 1/2 and 3/4 inch impact wrenches
use 3/8 inch (I .D .) fittings with 1/4 inch
NPT threads . Most compressors are
shipped with a short, 1/4 inch I .D . hose .
For proper performance and more
convenience, use a 3/8 inch I .D . hose .
Hoses longer than 50 feet should have a
1/2 inch I .D .
For 1 inch impact wrenches use 1/2 inch
(I .D .) fittings with 1/2 inch NPT threads
and a 1/2 inch I .D . hose . Hoses longer
than 50 feet should have a 1 inch I .D .

Never carry a tool

by the hose or

pull the hose to move the tool or a
compressor. Keep hoses away from
heat, oil and sharp edges. Replace any
hose that is damaged, weak or worn.

Storage

The impact wrench must be lubricated
before storing . Follow the air motor
lubrication instructions with an
exception to step 4 . Only run the impact
wrench for 2 to 3 seconds instead of 20
to 30 seconds because more oil needs
to remain in the impact wrench when
storing .

TECHNICAL SERVICE

For information regarding the
operation or repair of this product,
please call 1-800-543-6400 .

REPLACEMENT PARTS INFORMATION

For information regarding where to
order replacement parts, call toll free
1-800-543-6400 .
Please provide the following
information:
• Model number
• Stamped code
• Part number and description
Address parts correspondence to:
Campbell Hausfeld
100 Production Drive
Harrison, Ohio 45030 U .S .A .

RECOMMENDED HOOKUP

The illustration below shows the
recommended hookup for the tool .
1 . The air compressor

must be able to
maintain a minimum
of 60 PSI when the
tool is being used . An inadequate air
supply can cause a loss of power and
inconsistent driving .

2 . An oiler can be

used to provide oil
circulation through
the tool . A filter can
be used to remove liquid and solid
impurities which can rust or “gum
up” internal parts of the tool .

3 . Always use air supply hoses with

a minimum working pressure
rating equal to or greater than the
pressure from the power source if a
regulator fails, or 200 PSI, whichever
is greater . Use 1/4 inch air hose for
runs up to 50 feet . Use 3/8 inch air
hoses for 50 foot run or longer .

4 . Use a pressure regulator on the

compressor, with an operating
pressure of 0 PSI - 125 PSI . A pressure
regulator is required to control
the operating pressure of the tool
between 60 PSI and 90 PSI .

Recommended Hookup

Quick Coupler

(Optional)

Quick

Coupler

Air Hose

Lubricator

Quick Plug

(Optional)

Regulator

Filter

200 PSI or greater