8
www.campbellhausfeld.com
Operating Instructions
Distance From Cleaning Surface
The distance between the spray nozzle and the cleaning surface
is another factor that affects the impact force of the water. The
impact force of the water increases as the nozzle is moved closer
to the surface.
How to Avoid Damaging Surfaces
Damage to cleaning surfaces occurs because the impact force
of the water exceeds the durability of the surface. You can vary
the impact force by controlling the spray nozzle angle to the
cleaning surface and the distance from the cleaning surface
and by adjusting the spray nozzle. NEVER use a narrow high
impact stream on a surface that is susceptible to damage. Avoid
spraying windows with a narrow high impact stream. Doing so
may break the window. The most sure way to avoid damaging
surfaces is to follow these steps:
1. Place the spray nozzle approximately 4-5 feet (1,22-1,52 m)
away from the cleaning surface. Then hold the lance and
spray nozzle at a 45 degree angle to the cleaning surface.
Trigger the gun.
2. Vary the fan pattern spray angle and the distance to the
cleaning surface until optimum cleaning efficiency is achieved
without damaging the surface.
DETERGENT APPLICATION
NOTE:
Use only detergents formulated for pressure washers.
Test detergent in an inconspicuous area before use. DO NOT use
bleach in pressure washer.
Detergents
The use of detergents can dramatically reduce cleaning time
and assist in the removal of difficult stains. Many detergents are
customized for pressure washer use on specific cleaning tasks.
Pressure washer detergents are as thick as water. Using thicker
detergents – like dish detergent – will clog the chemical injection
system and prevent the application of the detergent.
Once applied to a cleaning surface, detergents take time to
break down dirt and grime. Detergents work best when applied
at low pressure.
You can effectively clean surfaces by combining the chemical
action of detergents with high pressure rinses. On vertical
surfaces, apply the detergent starting at the bottom and work
your way upward. This method prevents the detergent from
sliding down and causing streaks. Begin high pressure rinsing
at the top and work your way down to surface. On particularly
tough stains, use a brush in combination with detergents and
high pressure rinsing.
1. Follow manufacturer’s label directions for mixing correct
concentrations of detergent/detergents. The detergent
detergent to water ratio through the pump is approximately
10% (1 to 10).
◆
PW190100 & PW190200: Pour detergent into detergent
container.
General Cleaning Tips
1. Apply the detergent so that it thoroughly covers the cleaning
surface. Apply the detergent from bottom to top to prevent
the detergent from sliding down and streaking. Wait a couple
of minutes for the detergent to break down the dirt and grime.
Use a brush to lightly scrub heavily soiled areas. Never allow
the detergent to dry on the cleaning surface.
2. Rinse with high pressure.
CLEANING POWER
The easiest way to regulate the cleaning power of your pressure
washer is by changing the distance from the surface you are
cleaning. Begin spraying with a wide fan pattern while standing
several feet from the surface. Slowly move closer to the object
you are cleaning, adjusting the spray pattern as necessary, until
you find the most effective cleaning technique.
FINAL RINSE
The final rinse should start at the top and work down to surface.
Make sure that you thoroughly rinse the surface and that you
remove all detergent.
PRESSURE RELIEF PROCEDURE
To reduce the risk of bodily injury or property damage, always
follow this procedure whenever spraying is stopped, when work
is completed, and before checking or repairing any part of the
system.
1. Engage the trigger safety latch.
2. Turn the unit off.
3. Shut off the water supply.
4. Disengage the trigger safety latch and trigger the gun to
relieve pressure.
5. Re-engage the trigger safety latch.
6. When checking or repairing unit, remove the wall outlet plug
from the wall.
7. Before overnight storage, long term storage, or transporting
unit, disconnect the water supply.
SHUTDOWN
1. Fully rinse detergent attachement with clean water.
2. Turn the motor OFF.
3 Turn the water supply OFF.
4. After the motor and water supply are turned off, trigger the
gun to depressurize the system.
NEVER turn the water supply o
ff
before
turning the engine/motor o
ff
. Serious damage
could occur to the pump and/or engine/motor.
NEVER disconnect the high pressure
discharge hose from the machine while the
system is pressurized. To depressurize, turn engine/motor o
ff
, turn
water supply o
ff
and squeeze gun trigger 2-3 times.
5. After each use, wipe all surfaces of the pressure washer with
a clean, damp cloth.
Operation (Continued)
