Campbell Hausfeld HM7510 Operating Instructions Manual Download

Page: 3 / 24

HM7500 and HM7510

SPRAYING PRECAUTIONS

Do not spray

flammable materials

in vicinity of open flame or near ignition
sources including the compressor unit.

24. Spray in a well ventilated area, to keep

fumes from collecting and causing
health and fire hazards.

25. Do not spray in vicinity of open flames

or other places where a spark can
cause ignition. Do not smoke when
spraying paint, insecticides, or other
flammable substances.

26. Use a respirator when spraying.
27. Do not direct paint or other sprayed

material at the compressor. Locate
compressor as far away from
the spraying area as possible to
minimize overspray accumulation
on the compressor.

28. When spraying or cleaning with

solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.

29. Do not smoke when spraying paint,

insecticides, or other flammable
substances.

30. Use a face mask/

respirator when spraying
and spray in a well
ventilated area to
prevent health and fire
hazards.

31. Household use only.
32. To reduce the risk of electrical shock,

do not expose to rain. Store indoors.

Assembly

FOOT ASSEMbLY (FIGURE 1)

Foot assembly kit includes:

- 3 rubber feet

- 3 bolts

- 6 washers

- 3 nuts

Installation

LOCATION

It is extremely important to install the
compressor in a clean, well ventilated area
where the surrounding air temperature
will not be more than 100°F.
A minimum clearance of 18 inches between
the compressor and a wall is required
because objects could obstruct air flow.

Do not locate the

compressor air inlet

near steam, paint spray, sandblast areas
or any other source of contamination. This
debris will damage the motor.

Household use only. Store indoors.
ELECTRICAL INSTALLATION

1. Check and tighten all bolts, fittings,

etc., before operating compressor.

2. Operate compressor in a ventilated

area so that compressor may be
properly cooled.

3. Compressor should be located where

it can be directly plugged into an
outlet, but if this is not possible, an
extension cord may be used. It should
be selected using the extension cord
chart on page 3 as a guide.

4. To avoid loss of power and

overheating, it is better to use
additional air hose instead of
extension cords to reach work area.

WIRING

1. Local electrical wiring codes

differ from area to area. Source
wiring, plug and protector must
be rated for at least the amperage
and voltage indicated on motor
nameplate, and meet all electrical
codes for this minimum .

2. Use a slow blow fuse type T or a

circuit breaker.

overheating, short

circuiting and fire

damage will result from inadequate
wiring, etc.

All wiring and

electrical

connections should be performed by a
qualified electrician. installation must

be in accordance with local codes and
national electrical codes.

NOTE:

120 volt, compressor can be

operated on a 120 volt, 15 amp circuit
under the following conditions:

a. No other electrical appliances or

lights are connected to the same
branch circuit.

b. Voltage supply is normal.
c. Extension cords are of the

minimum gauge specified in this
instruction manual.

d. Circuit is equipped with a 15 amp

circuit breaker or a 15 amp slow
blow fuse type T.

3. If above conditions cannot be met

or if nuisance tripping of current
protection device occurs, it may be
necessary to operate compressor
from a 120 volt, 20 amp circuit.

GROUNDING INSTRUCTIONS

This product must be grounded. In
the event of an electrical short circuit,
grounding reduces the risk of electric
shock by providing an escape wire
for the electric current. This product
is equipped with a cord having a
grounding wire with an appropriate
grounding plug. The plug must be
plugged into an outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.

improper installation

of the grounding plug

is able to result in a risk of electric shock.
when repair or replacement of the cord or
plug is required, do not connect the
grounding wire to either flat blade
terminal. The wire with insulation having
an outer surface that is green with or
without yellow stripes is the grounding
wire.

Do not use adapter

with this product!

Power cord

White

Line

Motor cord

White

Load

Power cord

Black

Line

Yes