background image

Operating Instructions and Parts List

2

DC0300, FP2090, FP2091, FP2094 Series

GENERAL SAFETY

 Since the air compressor and other 
components (material pump, spray 
guns, filters, lubricators, hoses, 
etc.) used, make up a high pressure 
pumping system, the following safety 
precautions must be observed at all 
times:

 1.  Read all manuals 

included with this 
product carefully. Be 
thoroughly familiar with 
the controls and the 
proper use of the equipment.

 2.  Follow all local electrical and safety 

codes as well as in the United 
States, the National Electrical Codes 
(NEC) and Occupational Safety and 
Health Act (OSHA).

 3.  Only persons well acquainted 

with these rules of safe operation 
should be allowed to use the 
compressor.

4.  Keep visitors away and NEVER 

allow children in the work area.

5.  Wear safety glasses and 

use hearing protection 
when operating the unit.

6.  Do not stand on or use the unit as 

a handhold.

7.  Before each use, inspect 

compressed air system and 
electrical components for signs of 
damage,  deterioration, weakness 
or leakage. Repair or replace 
defective items before using.

8.  Check all fasteners at frequent 

intervals for proper tightness.

 Motors, 

  electrical 

equipment and controls can cause 
electrical arcs that will 
ignite a fl ammable gas 
or vapor. Never operate 
or repair in or near a 
fl ammable gas or vapor. 
Never store fl ammable 
liquids or gases in the vicinity of the 
compressor.

 

 Compressor parts 

may be hot even if the unit is stopped.

 9.  Keep fingers away from a 

running compressor; fast moving 
and hot parts will cause injury and/
or burns.

10. If the equipment should start 

to vibrate abnormally, STOP the 

engine/motor and 
check immediately for 
the cause. Vibration is 
generally a warning of 
trouble.

11. To reduce fire hazard, keep engine/

motor exterior free of oil, solvent, 
or excessive grease.

 

    

 

 

An ASME 

code

 

safety relief valve 

with a setting no higher 
than 125 psi MUST be installed in the 
tank for this compressor. The ASME 
safety valve must have suffi cient fl ow 
and pressure ratings to protect the 
pressurized components from bursting.

 See 

compressor 

  specifi cation decal 

for maximum operating pressure. 
Do not operate with pressure switch 
or pilot valves set higher than the 
maximum operating pressure.

12. Never attempt to adjust ASME 

safety valve. Keep safety valve 
free from paint and other 
accumulations.

 

Never use plastic

 (PVC) pipe for 

compressed air. Serious injury or death 
could result.

 Never 

  attempt to repair 

or modify a tank! Welding, drilling or 
any other modifi cation will weaken 
the tank resulting in damage from 
rupture or explosion. Always replace 
worn, cracked or damaged tanks.

 

 Drain liquid from 

 tank daily.

 13. Tanks rust from moisture build-up, 

which weakens the tank. Make 
sure to drain tank regularly and 
inspect periodically for unsafe 
conditions such as rust formation 
and corrosion.

14. Fast moving air will stir up dust 

and debris which may be harmful. 
Release air slowly when 
draining moisture or 
depressurizing the 
compressor system.

15. To reduce the risk of electrical 

shock, do not expose to rain. Store 
indoors.

 

 

  Indoor use only.

SPRAYING PRECAUTIONS

 

 

    Do not 

 

 

    spray fl ammable 

materials in vicinity of open fl ame or 

near ignition sources including the 
compressor unit.

 16. Do not smoke when spraying paint, 

insecticides, or other flammable 
substances.

17. Use a face mask / respirator when 

spraying and spray in a well 
ventilated area to prevent health 
and fire hazards.

18. Do not direct paint or other 

sprayed material at the compressor. 
Locate compressor as far away 
from the spraying area as 
possible to minimize overspray 
accumulation on the compressor.

19. When spraying or cleaning 

with solvents or toxic chemicals, 
follow the instructions 
provided by the chemical 
manufacturer.

HOSE PRECAUTIONS

20. Inspect hose before use.

 Do 

not 

 exceed working 

pressure marked on hose.

 

Do not  

 twist, 

 

bend knot, or abrade hose.

 21. Do not wrap hose 

around body.

 

 

    Keep   

 

                   away 

from hot surfaces and 
chemicals.

 Introduction

 R efer to Figure 3 to locate the 
following items.

ON / OFF Switch ( I / O ) - 

Push 

switch to the ON ( 

I

 ) position to turn 

compressor on. Push switch to the OFF 

O

 ) position to turn compressor off. 

This switch should be in the OFF ( 

O

 ) 

position when connecting / 
disconnecting power cord from 
electrical outlet or when changing 
tools.

MANUAL

Figure 1

www.campbellhausfeld.com

Summary of Contents for DC0300 Series

































Reviews: