2
Operating Instructions
www.campbellhausfeld.com
General Safety Information
(Continued)
•
Never use gasoline or
other flammable liquids to
clean the tool. Never use
the tool in the presence
of flammable liquids or
gases. Vapors could ignite by a spark
and cause an explosion which will
result in death or serious personal
injury.
•
Always remain in a firmly
balanced position when
using or handling the tool.
•
Do not remove, tamper
with, or otherwise
cause the Work Contact
Element (WCE) or
trigger to become
inoperable. Do not
operate any tool which
has been modified in a like fashion.
Death or serious personal injury
could result.
•
Do not touch the
trigger unless
driving fasteners.
Never attach air
line to tool or carry
tool while touching
the trigger. The tool could eject a
fastener which will result in death or
serious personal injury.
Warning indicates
a potentially
hazardous situation which, if not
avoided, could result in death or serious
injury.
•
Always disconnect
the tool from the
power source
when unattended,
performing any
maintenance or
work area are wearing ANSI Z87
eye protection equipment, and
when required, other appropriate
protection equipment such as
head, hearing and foot protection
equipment . Serious eye or
permanent hearing loss could result .
• Assuring that the tool is kept in safe
working order as described in this
manual .
eMployeR’S ReSpoNSIbIlITy:
• Selecting an appropriate tool
actuation system, taking into
consideration the work application
for which the tool is used .
• Ensuring that this manual is
available to operators and personnel
performing maintenance .
• The safe use of the tool.
• Enforcing that the tool
is used only when the
operator and all other
personnel in the work
area are wearing ANSI
Z87 eye protection equipment, and
when required, other appropriate
protection equipment such as
head, hearing and foot protection
equipment . Serious eye or
permanent hearing loss could result .
• Assuring that the tool is kept in safe
working order as described in this
manual .
• Assuring the proper maintenance of
all tools in employer’s possession .
• Ensuring that tools which require
repair are not further used before
repair . Tags and physical segregation
are recommended means of control .
GeNeRal SaFeTy
Danger indicates
an imminently
hazardous situation which, if not
avoided, will result in death or serious
injury.
•
Read and understand tool
labels and manual. Failure
to follow warnings,
dangers, and cautions
could result in DEATH or
SERIOUS INJURY.
•
Do not use any type of
reactive gases, including,
but not limited to, oxygen
and combustible gases,
as a power source. Use
filtered, lubricated, regulated
compressed air only. Use of a reactive
gas instead of compressed air may
cause the tool to explode which
will cause death or serious personal
injury.
•
Use only a pressure-
regulated compressed
air source to limit the
air pressure supplied to
the tool. The regulated
pressure must not exceed 100 psi.
If the regulator fails, the pressure
delivered to the tool must not
exceed 200 psi. The tool could
explode which will cause death or
serious personal injury.
•
ReqUIReS:
0 .8 SCFM with 10
fasteners per minute @ 90 psi
•
aIR INleT:
1/4 inch NPT
•
FaSTeNeR SIZe RaNGe:
3/8 inch to
1-1/4 inch
•
MaGaZINe CapaCITy:
100
fasteners per load, 18 gauge
•
STapleS:
1/4 inch crown
•
weIGhT:
2 lbs ., 15 oz .
•
leNGTh:
10-1/2 inch
•
heIGhT:
9-1/2 inch
• MAXIMUM PRESSURE:
100 psi
•
pReSSURe RaNGe:
60 - 100 psi
Tool Components and Specifications
Cap exhaust
Trigger
Quick clear nose
Work contact
element (WCE)
Fastener discharge area
Adjustable depth control
(not visible)
Magazine
Warning label
Latch button
O
CO
2
110 psi
MAX .
