CAME
32°C
10:55
p.
22
- M
a
n
u
a
l c
o
d
e:
F
A
0
0
3
2
3
-E
N
FA
0
0
3
2
3
-E
N
v.
11
0
2
/2
0
1
6 © C
A
M
E
S
.p.
A
. - T
h
e c
o
nte
n
ts of t
h
is
m
a
n
u
a
l m
ay b
e r
evi
se
d at a
n
y time, a
n
d wit
h
o
u
t n
o
ti
ce
.
WARNING!
important safety instructions for people:
READ CAREFULLY!
Danger of hand crushing
Danger! High voltage.
Premise
• Employ this product only for the use for which it was expressly made. Any
other use is dangerous. CAME Cancelli Automatici S.p.A is not liable for any
damage caused by improper, wrongful and unreasonable use • The safety
of this product and its proper fi tting depends, therefore, on respecting its
technical characteristics and proper fi tting, to be done in state-of-the-art
fashion, and under safe conditions as expressly explained in the literature that
comes with the product. • Keep these warnings together with the installation
and operation manuals that come with the operator.
Before installing
(do not continue until you have complied with all safety provisions)
• Fitting and testing must be only performed by qualifi ed technicians. Laying
the cables, installation and testing must follow state-of-the-art procedures
as dictated by regulations • Before beginning any operation it is mandatory
to carefully read all instructions as improper installation may result in serious
harm to people and things. • Make sure the door or leaf is in good mechanical
state, balanced and aligned, and that it opens and closes properly. Also, install
suitable protections, if needed, as well as additional safety sensors • If the
operator is to be installed at a height of over 2.5 m from the ground or other
access level, make sure you have any necessary protections and/or warnings
in place • If any pedestrian openings are fi tted into the operator, there must
also be a a system to block their opening while they are moving • Make sure
that the opening automated door or gate cannot entrap people against the
fi xed parts of the operator • Do not install the operator upside down or onto
elements that could yield and bend. If necessary, add suitable reinforcements
to the anchoring points • Do not install door or gate leaves on tilted surfaces
• Make sure any sprinkler systems cannot wet the operator from the ground
up • Make sure the temperature range shown on the product literature is
suitable to the climate where it will be installed as explained in the manual.
Installing
• Suitably section off and demarcate the entire installation site to prevent
unauthorized persons from entering the area, especially minors and children.
• Be careful when handling operators that weigh over 20 kg. If need be, use
proper safety hoisting equipment • The CE-marked safety devices (photocells,
stepping plates, sensitive safety-edges, emergency buttons, and so on), must
be fi tted in compliance with the regulations in eff ect and according to state-
of-the-art criteria, taking into account the environment, the type of required
service and of the working forces applied to moving leaves. Any shearing
or conveying points must be sensor-protected • Any residual risks must
be pointed out to endusers and highlighted with pictograms as provided by
the law. • All opening commands (that is, buttons, key switches, magnetic
readers, and so on) must be installed at least 1.85 m from the perimeter of
the gate's working area, or where they cannot be reached from outside the
gate. Also, any direct commands (buttons, touch panels, and so on) must
be installed at least 1.5 m from the ground and must not be reachable by
unauthorized persons • The automatic pedestrian closing must visibly show
its identifi cation data. • Before connecting the main power supply make sure
that the identifi cation data correspond to the those of the network • The
automatic pedestrian closing must be connected to an eff ective regulation
grounding system • The manufacturer declines any liability for using non-
original products; which would result in warranty loss • All maintained action
commands, must be fi tted in places from which the moving gate leaves
and transit and driving areas are visible • Apply, if missing, a permanent
sign showing the position of the release device • Before delivering to the
users, make sure the system is EN 12453 and EN 12445 standard compliant
(regarding impact forces), and also make sure the system has been properly
adjusted and that any safety, protection and manual release devices are
working properly • Apply Warning Signs where necessary and in a visible
place.
Special user-instructions and recommendations
• Keep gate operation areas clean and free of any obstructions. Make sure the
photocell's operating fi eld is clear of any obstructions • Do not allow children
to play with fi xed commands, or to loiter in the gate's maneuvering area.
Keep any remote control transmitters or any other command device away
from children, to prevent the operator from being accidentally activated.The
apparatus may be used by children of eight years and above and by physically,
mentally and sensorially challenged people, or even ones without any
experience, provided this happens under close supervision or once they have
been properly instructed to use the apparatus safely and about the potential
hazards involved. Children must not play with the apparatus. Cleaning and
maintenance must not be done by children, unless properly supervised •
Frequently check the system for any malfunctions or signs of wear and tear
or damage to the moving structures, to the component parts, all anchoring
points, including cables and any accessible connections. Keep any hinges,
moving joints and slide rails properly lubricated • Perform functional checks
on the photocells and sensitive safety edges, every six months. Constantly
clean the photocells' glass covers using a slightly water-moistened cloth; do
not use solvents or chemicals that could damage the devices • If repairs or
modifi cations are required to the system, release the operator and do not use
it until safety conditions have been restored • Cut off the power supply before
releasing the operator for manual openings and before any other operation,
to prevent potentially hazardous situations. Read the instructions • If the
power supply cable is damaged, it must be replaced by the manufacturer or
authorized technical assistance service, or in any case, by similarly qualifi ed
persons, to prevent any risk • It is FORBIDDEN for users to perform any
OPERATIONS THAT ARE NOT EXPRESSLY REQUIRED OF THEM AND WHICH ARE
NOT LISTED in the manuals. For any repairs, modifi cations and adjustments
and for extra-ordinary maintenance, CALL TECHNICAL ASSISTANCE • Log the
jobs and checks into the periodic maintenance log.
Additional special recommendations for everyone
• Keep away from hinges and mechanical moving parts • Do not enter the
operator's area of operation when it is moving • Do not counter the operator's
movement as this could result in dangerous situations • Always pay special
attention to any dangerous points, which have to be labeled with specifi c
pictograms and/or black and yellow stripes • When using a selector switch or
a command in maintained actions, keep checking that there are no persons
within the operating range of any moving parts, until the command is released
• The gate may move at any time and without warning • Always cut off the
power supply before performing any maintenance or cleaning.
