background image

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter

.

Si tiene dudas o comentarios, contáctenos.

1-855-558-2422 • www

.dewalt.com

INSTRUCTION MANUAL

GUIDE D’UTILISA

TION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SER

VICIO Y PÓLIZA 

DE GARANTÍA. 

ADVER

TENCIA: 

LÉASE ESTE INSTRUCTIVO ANTES 

DE USAR EL PRODUCTO.

DXMF4618WT

Adjustable W

elding T

able

Table de soudage ajustable

Mesa de soldadura ajustable

Copyright © 2019 D

E

WALT. 

D

E

WALT

®

 and the D

E

WALT Logo are trademarks of the D

E

WALT Industrial Tool Co., or an affiliate thereof 

and are used under license. The yellow/black color scheme is a trademark for D

E

WALT  

power tools & accessories. 

JS PRODUCTS  |  6445 MONTESSOURI STREET, LAS VEGAS, NV 89113

SAVE THESE INSTRUCTIONS

READ ALL INSTRUCTIONS

TECHNICAL SPECIFICATIONS

WARNING! Read and understand all instructions.

 

This manual contains 

important safety and operating instructions. 

Please read this manual carefully 

before assembling this welding table and save it for reference.

Technical Specifications

Total Capacity

1,000 lb (453.6 kg) 

*when weight is evenly distributed

Height

8" - 36" (20.3 cm - 91.4 cm)

Width

46" (116.8 cm)

Depth

18" (45.7 cm)

•  Read all instructions thoroughly.
•  Remove all components from the box, and lay them on the floor in an orderly fashion.
•  Wear eye protection.
•  Be cautious of sharp edges.
•  Keep this information for further reference.

(DEC 19)      Part No. 92796     DXMF4618WT     Copyright © 2019, D

E

WALT

ACCESSORIES

1.  Remove locking pins 

(2)

, grounding stud 

(3)

 and tool holder 

 

(4)

 

 from the hardware kit. Locate the holes 

on either end of the table. You will use both holes during assembly.

 2.  Remove the nut 

(3)

 from the grounding stud. From inside the table body, feed the grounding stud 

through the designated location (Fig 1). Place the nut and tighten to secure the grounding stud (Fig 2).

3.  Remove the nut from the tool holder. From outside the table body, feed the threaded portion of the  

tool holder through the designated location (Fig 3). Place the nut and tighten to secure the tool  

holder (Fig 4).

Assembly Instructions

GENERAL SAFETY

•  Keep work area clean and dry.
•  Use correct/recommended tools for the job.
•  Never leave unattended tools plugged in or running.
•  Wear appropriate safety apparel for the job you are doing.
•  Never crawl, sit, stand, or climb on the Welding Table.
•  Do not use this Welding Table while working with or around explosives or corrosive liquids. 
•  Before welding, always inspect the table to be sure it is in good condition.
•  Immediately remove work piece from the Welding Table if there is damage, bending, or warping

   of the legs or joints.
•  Maximum load capacity for the Welding Table is 1000 lb when evenly distributed.
•  Maximum point load capacity is 600 lb.
•  Before beginning any work, always secure leg locking pins once desired table height is set.

Tools Required for Assembly:

 (not included) 4 mm Hex Key or 4 mm Hex Bit, 8 mm Socket

BEFORE YOU BEGIN:

CORD MINDER

1.  Locate the leg with two (2) pass-through holes located at the top and bottom of the leg (Fig 5).
2.  Pass one (1) M5x57 

(11)

 bolt through the plastic cord snap, body of the leg and plastic cord minder 

(9)

 

making sure the tip of the cord minder attachment is pointing up towards the table top (Fig 6).

3.  Apply M5 nylon nut 

(13)

 and tighten.

4.  In the lower hole, pass one (1) M5x50 (10) bolt through the plastic cord snap 

(12)

, body of the leg and 

plastic cord minder; making sure the tip of the cord minder attachment is pointing down towards  

the bottom of the leg (Fig 8).

5.  Apply M5 nylon nut and tighten.
6.  Once assembled, extension cords can be wrapped around cord minders as well as snapped into

   cord snaps for cord management.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D

E

WALT TOOL, 

CALL US TOLL FREE AT: 

1-855-558-2422.

HANDLE

1.  Following the Operating Instructions in the next section, open the legs and stand the table up.
2.  Slide the handle bar 

(5)

 into the side of the table and through the square receivers underneath the 

table top (Fig 8).

3.  Insert M6x34 

(7)

 bolt through the side of the square receiver and apply M6 nylon nut 

(8)

 and  

tighten (Fig 8).

4.  Repeat step 3 for the other side of the handle.
5.  Insert M5x14 

(6)

 bolt through the bottom of the square receiver and tighten (Fig 9).

6.  Repeat step 5 for the other side of the handle.

- - - - 

- - 

 -- 

FIG. 1

FIG. 3

FIG. 2

FIG. 4

--

FIG. 6

--- 

-- 

-- 

FIG. 5

- - - 

-

-- 

FIG. 7

-- 

--- 

Parts List

No. Description

Qty.

1

Welding Table

1

2

Locking Pins

4

3

Grounding Stud

1

4

Tool Holder

1

5

Handle

1

6

Bolt M5x15mm

2

7

Bolt M6x30mm

2

No. Description

Qty.

8

M6 Nylon Nut

2

9

Cord Minder Brackets

2

10

Bolt M5x50mm

1

11

Bolt M5x57mm

1

12

Cord Snap

2

13

M5 Nylon Nut

2

Definitions: Safety Guidelines 

The definitions below describe the level of severity for each signal word. Please 
read the manual and pay attention to these symbols.

 

Indicates a potentially hazardous situation which, if not avoided, 

could

 

result in 

death or serious injury.

WARNING:

 

Indicates a potentially hazardous situation which, if not avoided, 

may

 

result in 

minor or moderate injury.

CAUTION:

(Used without word) Indicates a safety related message.

 

Indicates a practice 

not related to personal injury

 which, if not avoided, 

may

 result in 

property damage.

NOTICE:

2

5

13

12

7

8

6

3

4

11

10

9

11

Summary of Contents for DXMF4618WT

Page 1: ...on Immediately remove work piece from the Welding Table if there is damage bending or warping of the legs or joints Maximum load capacity for the Welding Table is 1000 lb when evenly distributed Maximum point load capacity is 600 lb Before beginning any work always secure leg locking pins once desired table height is set Tools Required for Assembly not included 4 mm Hex Key or 4 mm Hex Bit 8 mm So...

Page 2: ...the bottom position 6 To close reverse steps1 4 NOTE Be sure leg release pins engage housing to keep the legs secure while in the NOTE When ready for storage the locking pins 2 can be stored on each leg in the bottom hole Operating Instructions FIG 8 FIG 9 FIG 10 FIG 12 FIG 11 Leg Lock Button FIG 13 POIGNÉE 1 En suivant les consignes d utilisation de la section suivante ouvrez les pieds et levez l...

Page 3: ... Fig 11 5 Une fois que la hauteur de pied désirée est atteinte insérez les goupilles de verrouillage 2 dans le verrou du pied situé au dessus de la goupille de réglage Fig 12 Si la goupille de réglage est en position haute hauteur de pied la plus courte la goupille de verrouillage peut être insérée en position basse 6 Pour fermer inversez les étapes 1 à 4 REMARQUE Assurez vous que les goupilles de...

Page 4: ... Repita el paso 1 para cada pata por separado 3 Asegúrese de que cada pata esté bloqueada en su lugar y que la mesa esté sobre una superficie plana 4 Para extender las patas presione hacia abajo el botón de bloqueo de la pata y jale de esta hacia abajo figura 11 5 Una vez que se alcance la altura deseada de la pata inserte los pasadores de bloqueo 2 en el bloqueo de la pata que se encuentra por en...

Reviews: