Cambium Networks PMP 450 AP Installation Manual Download Page 34 | Manualshive

Page: 34 / 292

background image

Chapter 1: Product description

34

Band

BH

900 MHz

PTP 450/450i BHM and BHS

3.5 and 3.65 GHz

PTP 450/450b/450i BHM and BHS

4.9, 5.1, 5.2, 5.4 and 5.8 GHz

PTP 450b/450i/450b Retro BHM and BHS

5.4 and 5.8 GHz

PTP 450/450b/450i/450/450b Retro BHM and BHS

Typical deployment

The 450 Platform Family is an “all outdoor” solution consisting of a wireless bridge across sites. Each site
installation consists of an Integrated or Connectorized outdoor unit (ODU) and a power supply (PSU) (see
PMP/PTP 450 Platform Family typical bridge deployment). The ODU provides the following interfaces:

Ethernet port: This provides proprietary power over Ethernet and connection to the management and/or
data networks.

Note

PMP 450m 3 GHz has a separate power and data interface.

Figure 1 :

PMP/PTP 450 Platform Family typical bridge deployment

Note

Lightning Protection and Power supply differs for different variants.

Point-to-Multipoint

The PMP configuration of 450 Platform Family consists of Access Point (AP) and Subscriber Module (SM)
ODU. The radio link operates on a single frequency channel in each direction using Time Division Duplex

«
...
32
33
34
35
36
...
»

Summary of Contents for PMP 450 AP





































































































































































































































































































Reviews:

No comments

Related manuals for PMP 450 AP

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

Brand: Patton electronics Pages: 2

Brand: IBM Pages: 4

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 86

Brand: TFortis Pages: 86

Brand: dixell Pages: 4

Brand: Teknim Pages: 10

Brand: Eaton Pages: 14

Brand: IBASE Technology Pages: 39

Brand: CELOT Pages: 34

18x18 Card Cage

Brand: WolfPack Pages: 31

Brand: Nilox Pages: 66

LinkStation 500

Brand: Buffalo Pages: 139

Brand: Netopia Pages: 138

EdgePoint EP-R8

Brand: Ubiquiti Pages: 22

Brand: Pakedge Pages: 8

BreezeACCESS II

Brand: Alvarion Pages: 324

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands