Cambium Networks PMP 450 AP Installation Manual Download Page 29

Page: 29 / 292

Chapter 1: Product description

Characteristic

Value

Duplexing

TDD (symmetric and asymmetric)

Connectivity

100Base-T Ethernet Main port with PoE input

Operating frequencies

900 MHz, 2.4 GHz, 3.5 GHz, 3.65 GHz and 5 GHz

Tx Power - conducted

max 22 dBm (2.4 GHz and 5 GHz)

max 25 dBm (3.5 GHz and 3.65 GHz)

max 25 dBm (900 MHz - PMP 450 SM and BH)

Channel bandwidth

5, 7, 10, 15, 20, 30, and 40 MHz

Note

All bands do not support all channel
bandwidths. For more information,
refer to this

link

High spectral efficiency

Up to 7.5 bps/Hz

Timing synchronization CMM4, CMM5, internal GPS or UGPS/cnPulse

Data rate

Up to 310 Mbps (40 MHz channel BW) for PMP/PTP

Frequency bands

The PMP/PTP 450 Series ODU can operate in the following bands:

900 MHz band: 902 to 928 MHz (SM and BH)

2.4 GHz band: 2400 to 2483 MHz

3.5 GHz band: 3300 to 3600 MHz

3.65 GHz band: 3500 to 3850 MHz

5 GHz band: 5470 to 5875 MHz

Hardware components

The main hardware components of the PMP/PTP 450 are as follows:

PMP 450 AP

PMP 450 SM

PTP 450 BH (BHM/BHS)

The PMP/PTP 450 is supplied in the following configurations:

Summary of Contents for PMP 450 AP





































































































































































































































































































Search results

Summary of Contents for PMP 450 AP

Reviews:

Related manuals for PMP 450 AP

Brands by name

Popular brands

Cambium Networks PMP 450 AP, Installation Manual

Search results

Summary of Contents for PMP 450 AP

Reviews:

Related manuals for PMP 450 AP

Brands by name

Popular brands