background image

Oxygen Concentrator

 16

CAUTION

DO NOT connect the Companion 5 to an

extension cord or electrical outlet controlled

by a switch.

Always check to see that the Air Inlet and

the Exhaust Vent are not blocked.

Disconnecting the AC Power

To ensure that there is no power to the Companion 5, 

unplug from AC power.

Note: Turn the Companion 5 to the “Off” (O) position to avoid 

alarming before disconnecting the AC Power cord. 

Using Around the House

Patient may use up to 50 ft (15.24 m) of oxygen tubing and a 7 ft (2.14 

m) standard nasal cannula with the Companion 5.  If using a

humidifier bottle with long tubing runs, always verify the flow meter still

reads the patient’s prescribed rate after installation.

CAUTION

When using a humidifier adapter of any kind, 

the Companion 5 unit must remain stationary, 

meaning that the unit must NOT be moved or 

transported in any manner to avoid damage to 

the Companion 5.

Locating the Companion 5 for Proper 
Use and Ventilation

Ask your patient where they would like to set up the device. 

Whenever possible, the Companion 5 should be in the same 

room as the patient for convenience and assurance that the 

patient can adequately hear and respond to Companion 5 alerts 

and alarms. While unpacking and setting up the device, tell 

your patient about these important cautions and warnings:

WARNING: LOCATE THE COMPANION 5 IN A WELL-VENTILATED 
SPACE THAT PROVIDES ADEQUATE AIRFLOW.

WARNING: ENSURE THAT FURNITURE, DRAPERIES OR CLOTHING 

WILL NOT IMPEDE AIR CIRCULATION.

WARNING: AVOID PLACING THE UNIT OVER A FLOOR HEAT REGISTER OR 
AGAINST A BASEBOARD HEATING SYSTEM.

WARNING: DO NOT USE IN THE PRESENCE OF FLAMMABLE ANESTHETICS, 
SOLVENTS, AEROSOLS OR FLAMMABLE CLEANING AGENTS.

WARNING: AVOID HIGH POLLUTANT ENVIRONMENTS.

CAUTION

Some patients are highly mobile and may use 

the device under varying circumstances. Make 

sure your patient or patient caregiver 

completely understands the basic precautions 

to safely locate the device.

Note: After completing this training procedure, ask your patient if 

he/she has any questions.

Power On and Warm Up

Plug the electrical cord of the CAIRE Companion 5 into an 

AC outlet.

WARNING: INSPECT THE ELECTRICAL CORD FOR DAMAGE  
BEFORE USE. IF THE CORD IS DAMAGED, DO NOT PLUG IT INTO 
AN ELECTRICAL OUTLET OR ATTEMPT TO OPERATE THE  

CONCENTRATOR.

Press the power switch in the “ON” (I) position

.

When the Companion 5 is plugged in properly and turned on, 

a green indicator on the LED Display will light up. 

All LED 

lights will illuminate upon start up. After the concentrator 

completes the warn-up cycle, only the green light will remain 

on. 

The O2 Light will illuminate for four (4) seconds upon start-up. 

After this initial start-up, this light is disabled for approximately 

ten (10) minutes while the concentration rises to 

specifications.

Note:

 After Initially powering on, the O2 light will illuminate

 

and “O2 UP” will display on the screen until the concentration

 

reaches specifications.

Summary of Contents for Companion 5







































Reviews: