background image

31-7000166   Rev.1

3

Installation Instructions

24” DRAWER MICROWAVE MEASUREMENTS

•  

Figures 1 and 2 contain many drawer microwave measurements for reference when planning the drawer location.

•  This drawer microwave can be installed below any electric or gas wall oven or under selected cook  

top models.

•  Can also be installed using an electrical outlet in an adjacent cabinet within the areas where the provided electrical 

cord can reach. Power cord access hole in cabinet should be a minimum of 1 1/2” diameter hole and deburred of 
all sharp edges.

IMPORTANT

•  Always allow sufficient power cord length to the electrical outlet to prevent tension.

• Always check electrical codes for requirements.

Preferred electrical 
outlet location*

6”

5”

4”

22 1/8”

7/8” 

overlap

7/8” 

overlap

231/2”

min

Anti-Tip 

Block

31/2”

14 13/16” to

 

bottom of  

anti-tip 

block

36” 

countertop 

height

24” 

cabinet min.

18 1/2” to 

top of floor

Floor 

must 

support 

100 lbs

1/16” 

overlap

11/16” 

overlap

14 13/16” 

Figure 1

21 5/8”

15 15/16”

23 7/8”

1419/32”

21 5/8”

1 5/8” door 

thickness

15” auto 
drawer 
opening

Figure 2

ANTI-TIP BLOCK

NORMAL INSTALLATION STEPS

Anti -Tip BLOCK Installation Instructions

To reduce the risk of tipping of the drawer, the Anti-Tip block must be properly 
installed located 14 13/16-inches above the floor on which the Drawer 
Microwave will sit. The anti-tip block must be provided and pre-installed by the 
purchaser of the product or builder before install can be done. The anti-tip block 
is not provided by installer. See Figures 1 and 2. The Anti-Tip block prevents 
serious injury that might result from spilled  
hot liquids.

If the Drawer Microwave is ever moved to a different location, the Anti-Tip block 
must also be moved and installed. When installed to the wall, make sure that 
the screws completely penetrate the dry wall and are secured in wood or metal 
so that the block is totally stable. When fastening, be sure that the screws do 
not penetrate electrical wiring or plumbing.

3 1/2”

6”

Anti-Tip 

block

Figure 3

Summary of Contents for CWL112P4RW5

















Reviews: