Cadman 6003, Operator'S Parts And Maintenance Manual

Page: 12 / 26

TR-MAN-6003
3-POINT HITCH HOSE CADDY
Page 10 of 24
Step 3
Once on site, engage the tractor hydraulics so that the drum
rotates away from the rear of the tractor. This will allow the soft
hose to unreel.
Step 4
As you unreel the soft hose drive the tractor (at a low rate of
speed) along the required hose path.
Figure 4 - Unreel Hose Slowly
img-00170.wmf
Step 5
When the soft hose is nearing the last wrap stop the tractor and disengage the
hydraulics. Slowly rotate the drum so that the hose end fitting can be easily removed.
Step 6
To prevent damage to the hose fitting, remove the hose end manually from the Hose
Caddy.
OPERATOR NOTE
Where field conditions
permit, always attempt
to pull the hose either
up or down sloping
terrain instead of
operating across a
side hill.
SAFETY FIRST!
TR-MAN-6003
3-POINT HITCH HOSE CADDY
Page 15 of 24
Frame Assembly
∗
6003
(All Models)
Item Description Part Number Qty
1 BEARING RETAINING PLATE 05-622 2
2 UPPER HITCH PIN 13-397 1
3 LOWER HITCH PIN 13-405 2
4 DRUM DRIVE LUG 15-040-B 12
5 FRAME, HOSE CADDY 3PT HITCH 19-400 1
6 DRUM WELDMENT 19-500 1
7 CHAIN GUARD WELDMENT 19-601 1
8 TOOL BOX DOOR 19-602 2
9 BRASS HINGE PIN 19-603 2
10 LABEL - GREASE POINT 40-041-A 1
11 LABEL - ENTANGLEMENT 40-051-A 1
12 RUBBER LATCH KIT - LATCH 40-217 2
13 CADMAN SERIAL NUMBER TAG 40-238 1
14 LABEL - ROTATING DRUM 40-287-B 3
15 DECAL - 3 POINT HOSE CADDY PANEL 40-530-6003 2
16 DECAL - AMBER REFLECTIVE 40-598 4
17 DECAL - RED REFLECTIVE 40-599 4
18 2 1/2 IN. PILLOW BLOCK BEARING 40-602 2
19 DECAL - CADMAN 3 PT HOSE DRUM 40-706 4
20 LABEL - LIFT POINT 40-933 4
21 LABEL - TIE DOWN POINT 40-947 4
22 LABEL - OPERATOR MANUAL 42-050 1
23 MANUAL PAK - SMALL 42-070 1
24 5/8-11 X 1.25 STAINLESS STEEL BOLT 88-BLT-06311X125 2
25 3/4-10 X 2.00 STAINLESS STEEL BOLT 88-BLT-07510X200 4
26 1/2-13 STAINLESS STEEL JAM NUT 88-NUT-JAM050-13 12
27 1/2 STAINLESS STEEL LOCK WASHER 88-WSR-LOC050 12
28 5/8 STAINLESS STEEL LOCK WASHER 88-WSR-LOC063 2
29 3/4 STAINLESS STEEL SAE FLAT WASHER 88-WSR-SAE075 4
30 5/16-18X3/4 LG. FLANGE HEAD BOLT 90-BLT-F03118X075 2
31 LYNCH PIN - STANDARD 90-PIN-LYNCH 5
32 3/16 X 3/8 IN. RIVET 90-RIV-019X038 10
33 1/4 X 0.75 TEK SCREW 90-SCR-TEK025X075 3
34 1/4 X 1.00 TEK SCREW 90-SCR-TEK025X100 2
35 1/4 NYLON FLAT WASHER 90-WSR-FLT025NYLON 2