Cadillac SRX 2016 Owner'S Manual Download Page 40 | Manualshive

Page: 40 / 382

background image

Cadillac SRX Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-

9087647) - 2016 - crc - 5/4/15

Keys, Doors, and Windows

39

.

Press the touch pad on the
liftgate outside handle after
unlocking all doors.

Press and release

8

on the

liftgate next to the latch to close the
liftgate.

Pressing any liftgate button, or the
touch pad while the liftgate is
moving, stops it. Pressing again
reverses the direction. There is a
minimum distance that the power
liftgate must already be open for the
system to hold it open. If movement
is stopped below that minimum, the
liftgate closes.

Do not force the liftgate open or
closed during a power cycle. This
may activate the system's obstacle
detection feature and stop the
power operation.

The power liftgate may be
temporarily disabled under extreme
temperatures or low battery
conditions. If this occurs, the liftgate
can still be operated manually.

If you shift the transmission out of
P (Park) while the power function is
in progress, the liftgate power
function will continue to completion.
If you shift the transmission out of
P (Park) and accelerate before the
power liftgate latch is closed, the
liftgate may reverse to the open
position. Cargo could fall out of the
vehicle. Always make sure the
power liftgate is closed and latched
before you drive away.

If after a power opening, the liftgate
stays open momentarily, then slowly
closes with continuous chiming
sounds and turn signal flashes, the
support strut may have lost
pressure. See your dealer for
service before using the liftgate.

Obstacle Detection Features

If the liftgate encounters an obstacle
during a power open or close cycle,
a warning chime will sound and the
liftgate will automatically reverse
direction to the full closed or open
position. After removing the
obstruction, the power liftgate
operation can be used again. If the
liftgate encounters multiple
obstacles on the same power cycle,
the power function will deactivate.
After removing the obstructions, the
liftgate will resume normal power
operation.

The vehicle has pinch sensors on
the side edges of the liftgate. If an
object is caught between the liftgate
and the body and presses against
one of these sensors, the liftgate will
reverse direction and open fully. The
liftgate will remain open until it is
activated again or closed manually.

Setting the 3/4 Mode

To change the liftgate stop position:

1. Select MAX or 3/4 mode and

open the liftgate.

«
...
38
39
40
41
42
...
»

Summary of Contents for SRX 2016































































































































































































































































































































































































Reviews:

No comments

Related manuals for SRX 2016

Brand: Honda Pages: 208

Brand: Hama Pages: 4

Brand: Volvo Pages: 230

Brand: Hama Pages: 13

Brand: Rhino-Rack Pages: 2

transit connect 2012

Brand: Ford Pages: 299

Brand: ULTIMATE SPEED Pages: 132

Brand: Toyota Pages: 277

Brand: Hollywood Racks Pages: 8

403.NISS4HT 2.36 RSR

Brand: Directed Pages: 22

DynaSport Roof Rack

Brand: Perrycraft Pages: 4

Brand: Toyota Pages: 307

Brand: Myenergi Pages: 36

Brand: Kia Pages: 38

Brand: Chevrolet Pages: 416

Omvl DREAM XXI E

Brand: Westport Pages: 5

Brand: Rover Group Pages: 94

Brand: rough country Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands