Cadillac SRX 2016 Owner'S Manual Download Page 29 | Manualshive

Page: 29 / 382

background image

Cadillac SRX Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-

9087647) - 2016 - crc - 5/4/15

28

Keys, Doors, and Windows

With Remote Start and Power

Liftgate Shown, Without Similar

Q

(Lock) :

Press to lock all doors.

The turn signal indicators may flash
and/or the horn may sound on the
second press to indicate locking.
See

Vehicle Personalization

0

147

.

If the driver door is open when

Q

is

pressed, all doors lock except the
driver door, if enabled through the
vehicle personalization. If the
passenger door is open when

Q

is

pressed, all doors lock.

Pressing

Q

may also arm the

theft-deterrent system. See

Vehicle

Alarm System

0

40

.

If equipped, pressing

Q

will also

lock the fuel door.

K

(Unlock) :

Press to unlock the

driver door or all doors. See

Vehicle

Personalization

0

147

. When

remotely unlocking the vehicle at
night the fog lamps and back-up
lamps will come on for about
20 seconds to light your approach to
the vehicle. The turn signal
indicators may flash to indicate
unlocking. See

Vehicle

Personalization

0

147

.

Pressing

K

will disarm the

theft-deterrent system. See

Vehicle

Alarm System

0

40

.

On some models, pressing and
holding

K

will open all of the

windows.

If equipped, pressing

K

will also

unlock the fuel door.

/

(Remote Start) :

For vehicles

with this feature, press and
release

Q

and then immediately

press and hold

/

for at least

four seconds to start the engine

from outside the vehicle using the
RKE transmitter. See

Remote

Vehicle Start

0

33

.

7

(Vehicle Locator/Panic

Alarm) :

Press and release one

time to initiate vehicle locator. The
exterior lamps flash and the horn
chirps three times. Press and
hold

7

for three seconds to sound

the panic alarm. The horn sounds
and the turn signal lamps flash for
30 seconds, or until

7

is pressed

again or the vehicle is started.

b

(Remote Liftgate Release) :

Press twice to open or close the
liftgate.

Press once to stop the liftgate from
moving.

Keyless Access Operation

With the Keyless Access system,
you can lock and unlock the doors
and access the hatch without
removing the RKE transmitter from
your pocket, purse, briefcase, etc.
The RKE transmitter should be
within 1 m (3 ft) of the door or hatch
being opened.

«
...
27
28
29
30
31
...
»

Summary of Contents for SRX 2016































































































































































































































































































































































































Reviews:

No comments

Related manuals for SRX 2016

Brand: Dakota Digital Pages: 2

Brand: Dakota Digital Pages: 7

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: LAMBORGHINI Pages: 48

Brand: Ford Pages: 22

Brand: Ford Pages: 256

Brand: v.link Pages: 12

Brand: ULTIMATE SPEED Pages: 34

Crossland X 2017

Brand: Vauxhall Pages: 245

Brand: Easee Pages: 21

Brand: Pyle Pages: 14

Brand: Edelbrock Pages: 4

Brand: Volkswagen Pages: 11

Brand: walser Pages: 8

Brand: Honda Pages: 76

IONIQ HYBRID 2019

Brand: Hyundai Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands