manualshive.com logo in svg

Cadillac SRX 2016, Owner'S Manual

The Cadillac SRX 2016 Owner's Manual is an essential companion for every SRX owner. With our user-friendly website, you can easily and freely download this comprehensive manual, providing you with all the necessary information to maximize your driving experience. Don't miss the opportunity to access it at manualshive.com.

Share
Download
background image

Cadillac SRX Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-

9087647) - 2016 - crc - 5/4/15

200

Driving and Operating

The vehicle may automatically apply
the EPB in some situations when
the vehicle is not moving. This is
normal, and is done to periodically
check the correct operation of the
EPB system.

If the EPB fails to apply, the rear
wheels should be blocked to
prevent vehicle movement.

EPB Release

To release the EPB:

1. Place the ignition in ACC/

ACCESSORY or ON/RUN.

2. Apply and hold the brake

pedal.

3. Push down momentarily on the

EPB switch.

The EPB is released when the red
parking brake status light is off.

If the amber parking brake warning
light is on, release the EPB by
pushing down on the EPB switch
and holding it down. Continue to
hold the switch until the red parking
brake status light is off. If either light
stays on after release is attempted,
see your dealer.

Caution

Driving with the parking brake on
can overheat the brake system
and cause premature wear or
damage to brake system parts.
Make sure that the parking brake
is fully released and the brake
warning light is off before driving.

Automatic EPB Release

The EPB automatically releases
differently on vehicles with and
without Adaptive Cruise Control
(ACC). Avoid rapid acceleration
when the EPB is applied, to
preserve parking brake lining life.

.

With ACC, the EPB will
automatically release when the
engine is running, the brake
pedal is applied, and the
transmission is shifted out of
P (Park).

.

Without ACC, the EPB will
automatically release when the
engine is running, the
transmission is placed into gear,

and an attempt is made to drive
away by pressing the
accelerator pedal.

If parking on a hill, or if the vehicle
is pulling a trailer, see

Driving

Characteristics and Towing Tips

0

229

.

Brake Assist

The Brake Assist feature is
designed to assist the driver in
stopping or decreasing vehicle
speed in emergency driving
conditions. This feature uses the
stability system hydraulic brake
control module to supplement the
power brake system under
conditions where the driver has
quickly and forcefully applied the
brake pedal in an attempt to quickly
stop or slow down the vehicle. The
stability system hydraulic brake
control module increases brake
pressure at each corner of the
vehicle until the ABS activates.
Minor brake pedal pulsation or
pedal movement during this time is
normal and the driver should
continue to apply the brake pedal as

Summary of Contents for SRX 2016































































































































































































































































































































































































Reviews:

No comments

Related manuals for SRX 2016

Streetwize LeisureWize EMOVE EM303A Manual preview
LeisureWize EMOVE EM303A
Brand: Streetwize Pages: 20
John Gold Gold Cruuse Cruisecontrol GC90 Installation Manual preview
Gold Cruuse Cruisecontrol GC90
Brand: John Gold Pages: 24
Whispbar K498W Fitting Instructions Manual preview
K498W
Brand: Whispbar Pages: 14
Easee Home Wallbox Installation Instructions Manual preview
Home Wallbox
Brand: Easee Pages: 12
NanoCam Plus NCP-MIRDVR522 User Manual preview
NCP-MIRDVR522
Brand: NanoCam Plus Pages: 32
Yakima K614 Manual preview
K614
Brand: Yakima Pages: 12
FALCON RIDGE CF-1000-WD05 Instructions For Installation And Care preview
CF-1000-WD05
Brand: FALCON RIDGE Pages: 6
AMP Research BEDXTENDER HD MAX 74841-00A Assembly Installation Manual preview
BEDXTENDER HD MAX 74841-00A
Brand: AMP Research Pages: 9
Belkin F8V7058-APL User Manual preview
F8V7058-APL
Brand: Belkin Pages: 2
Maserati Grecale 2023 Owner'S Manual preview
Grecale 2023
Brand: Maserati Pages: 302
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Brand: ECS Pages: 4
Whispbar WB751 Manual preview
WB751
Brand: Whispbar Pages: 15
Cadillac Fleetwood Brougham Sedan 1966 Owner'S Manual preview
Fleetwood Brougham Sedan 1966
Brand: Cadillac Pages: 56
Cadillac 2005 XLR Owner'S Manual preview
2005 XLR
Brand: Cadillac Pages: 438
PMT AS7.M100.001 User Manual preview
AS7.M100.001
Brand: PMT Pages: 16
RAWLINK 36772 Instruction Manual preview
36772
Brand: RAWLINK Pages: 25
Fortin Electronic Systems EVO-CAN Suggested Wiring Configuration preview
EVO-CAN
Brand: Fortin Electronic Systems Pages: 5
T-Rex TEX-51127 Installation Manual preview
TEX-51127
Brand: T-Rex Pages: 9

Brands by name

Popular brands

Load more brands