Cadillac 2202 Escalade EXT Manual Download Page 272 | Manualshive

Page: 272 / 427

background image

4-55

Making Turns

NOTICE:

Making very sharp turns while trailering could
cause the trailer to come in contact with the
vehicle. Your vehicle could be damaged. Avoid
making very sharp turns while trailering.

When you’re turning with a trailer, make wider turns than
normal. Do this so your trailer won’t strike soft shoulders,
curbs, road signs, trees or other objects. Avoid jerky or
sudden maneuvers. Signal well in advance.

Turn Signals When Towing a Trailer

The arrows on your instrument panel will flash
whenever you signal a turn or lane change. Properly
hooked up, the trailer lamps will also flash, telling other
drivers you’re about to turn, change lanes or stop.

When towing a trailer, the arrows on your instrument
panel will flash for turns even if the bulbs on the trailer
are burned out. Thus, you may think drivers behind you
are seeing your signal when they are not. It’s important
to check occasionally to be sure the trailer bulbs are
still working.

Driving On Grades

Reduce speed and shift to a lower gear before you start
down a long or steep downgrade. If you don’t shift
down, you might have to use your brakes so much that
they would get hot and no longer work well.

You can tow in DRIVE (D). You may want to shift the
transmission to THIRD (3) or, if necessary, a lower gear
selection if the transmission shifts too often (e.g., under
heavy loads and/or hilly conditions).

You may also want to activate the tow/haul mode if the
transmission shifts too often. See “Tow/Haul Mode”
in the Index.

When towing at high altitude on steep uphill grades,
consider the following: Engine coolant will boil at a
lower temperature than at normal altitudes. If you
turn your engine off immediately after towing at high
altitude on steep uphill grades, your vehicle may show
signs similar to engine overheating. To avoid this,
let the engine run while parked (preferably on level
ground) with the automatic transmission in PARK (P)
for a few minutes before turning the engine off. If you
do get the overheat warning, see “Engine Overheating”
in the Index.

«
...
270
271
272
273
274
...
»

Summary of Contents for 2202 Escalade EXT












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2202 Escalade EXT

Brand: Ranger design Pages: 6

Brand: EAL Pages: 4

Brand: Metra Electronics Pages: 2

Brand: Car-Interface Pages: 23

Brand: RuggON Pages: 2

Brand: GMC Pages: 499

Brand: Kia Pages: 290

Brand: Ford Pages: 37

Brand: Würth Pages: 36

Brand: AddSecure Pages: 14

Brand: Beper Pages: 52

Brand: Bestop Pages: 4

2007 SLR Mclaren

Brand: Mercedes-Benz Pages: 425

Brand: Cadillac Pages: 20

Brand: Pyle Pages: 8

Brand: Mobridge Pages: 20

TuneBase F8Z442

Brand: Belkin Pages: 162

Brand: Dacia Pages: 244

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands