manualshive.com logo in svg

BYD Battery-Box LV Flex Lite, Operating Manual

Share
Download
BYD Battery-Box LV Flex Lite Operating Manual Download Page 30

  9 

Decommissioning

 

 

29 

9. Decommissioning

Risk of injury due to weight of the battery module 

Injuries may result if the battery module is lifted incorrectly or dropped while being transported or 

installed. 

• Transport and lift the battery module carefully. Take the weight of the battery module into

account. 

• Wear suitable personal protective equipment for all work on the battery system.

Procedure: 

1. Shut off the inverter.

2. Switch off the battery system.

3. Switch off the breaker between the inverter and the battery system if there is any.

4. Disconnect the DC cables between inverter and the battery system, PE, and data cable among

battery system, inverter, BMU and router (if applicable).

5. Loose the screws between battery modules.

If the battery system is to be stored or shipped, pack the system. Use the original packaging or 

packaging that is suitable for the weight and dimensions of the system. 

Dispose of the battery system in accordance with the locally applicable disposal regulations for 

electronic waste.

Shen

z

hen BYD Electronic Co.

,

 

L

TD

Summary of Contents for Battery-Box LV Flex Lite







































Reviews:

No comments

Brands by name

Popular brands

Load more brands