Burnside T400FX User Manual Download Page 22

Page: 22 / 25

Page 22 of 25

Rev 2.1

Technical Specifications

Operational Requirements

GSM Systems.

2G GSM Quad-band GSM phase 2/2+ 850/900 @ 33dBm max.,
1800/1900 MHz @ 30dBm max.

Signal sensitivity

-90dBm or better recommended for reliable operation

Not suitable for
connection to:

3G Networks

GSM-R Networks

Power supply

12VDC Standby 0.15W, On call 1.9W average.

AC adapter supplied 100

– 240Vac 50/60Hz.

Battery backup

User exchangeable 1900mAH AA size NiMH batteries

Over 50 hours standby or 5 hours talk time (TS.09-v7.6).

Indicators

Red, green and amber LEDs.

Speech codecs

HR, FR, EFR & AMR

GSM In-call features Call waiting, multiparty calls and explicit call transfer.

FXS specification

BT431A connector for UK model, RJ11 connector for EU model

DC loop current 20/25/30mA (user selectable, default 25).

Ringing signal 25Hz sinusoidal 60V RMS

Ringing load 3 REN

Dialling by DTMF

CLI passed through from FXO.

CLI generated from incoming Mobile call.

FXO specification

RJ11 connector

On-hook and off-hook line voltage monitor



A on-hook line current monitor

Loop current monitor

Parallel handset detection

Line polarity reversal detection

Greater than 3000V isolation

Antenna connection 50 Ohm SMA male connector

Monitored faults and
sensors

•

Power break

•

PSTN failure

•

Battery condition

•

Supply voltage

•

Ambient temperature

Monitoring method

•

Remote interrogation by SMS.

•

SMS sent on event.

Summary of Contents for T400FX


























Search results

Summary of Contents for T400FX

Reviews:

Related manuals for T400FX

Brands by name

Popular brands

Burnside T400FX, User Manual

Search results

Summary of Contents for T400FX

Reviews:

Related manuals for T400FX

Brands by name

Popular brands